[spider.git] / txt / wininstallation.txt

  The Installation Guide for DXSpider under Microsoft Windows
  Iain Philipps, G0RDI (g0rdi@77hz.com)
  $Date$ $Revision$

  DX Spider under Microsoft Windows (TM)
  ______________________________________________________________________

  Table of Contents


  1. Introduction

     1.1 The requirements
     1.2 The system
     1.3 Perl
     1.4 Additional packages
     1.5 Getting Spider

  2. Installing the software

     2.1 The AGW packet engine
     2.2 Setting up the initial user files
     2.3 Incoming telnets
     2.4 Connecting to other clusters


  ______________________________________________________________________

  1.  Introduction

  IMPORTANT:

  What you'll be left with once you've followed these instructions is
  (hopefully) a working DX Spider v1.47 system that is capable of
  accepting or originating "internet" connections, plus inbound AX.25
  and TCP/IP radio connections. If the absence of outbound radio
  connections is a serious limitation for you, it would be better for
  you to wait a couple more weeks until this support has been added.

  On the other hand, you may have an enquiring mind, or better yet, may
  be looking for a useful way of connecting your current (perhaps) AK1A
  cluster "to the internet" via some networking mechanism (BPQEther,
  etc) or other. I won't be producing instructions for the latter case,
  because I don't have an AK1A to play with. But someone might ...

  Whatever, this document is intended to get you started with DX Spider
  in a Microsoft Windows (TM) environment. It's not intended to teach
  you anything other than how to perform a minimum configuration of a DX
  Spider installation and have it able to connect across "the internet"
  to other DX Clusters, while accepting inbound TELNET and radio
  connections.


  1.1.  The requirements

  The very first things you're going to need are (in order of
  importance):-


  o  A cup of good, strong tea

  o  A supported Windows platform with an internet connection so you can
     download the necessary software bits and bobs directly to it. There
     are other ways, but this is preferable.


  o  Another cup of good, strong tea

  o  If all goes according to plan, about an hour to spare

  o  Plenty of good, strong tea


  1.2.  The system

  The platform I used to generate these instructions was a "vanilla"
  Microsoft Windows Me 4.90.3000 system, with a 700MHz AMD Athlon
  processor and 96 Mb memory. I've also personally verified that it runs
  on my laptop (Pentium 266MHz, 32 Mb memory, Windows 98 SE v4.10.2222
  A) and a computer that I assembled from a random pile of junk (AMD
  K6-2 333MHz, 64 Mb memory, Windows 98 v4.10.1998). As a result, I have
  reason to believe that what I'm about to describe will perform equally
  on any 32-bit MS Windows environment with 32 Mb of memory.

  Because of the changes that have recently been made to the core
  "cluster.pl" module and the introduction of a very lightweight
  "winclient.pl", I have a sneaking suspicion that this will now run on
  any platform that has reasonably complete support for Perl. Is there
  someone out there with both an enquiring mind and (say) a Macintosh,
  for instance?

  Please bear in mind, though, that my instructions relate solely to how
  to get this going under a Microsoft Windows environment, and I have
  zero intention of trying to make them say otherwise.


  1.3.  Perl

  Install your chosen Perl environment. Unless you have a very good
  reason for not doing so, I strongly suggest that you use ActivePerl
  v5.6. For my testing & development, I used build 623.  You can get
  this from:-
  http://www.activestate.com/Products/ActivePerl/Download.html

  You will need to choose either the MSI or the AS package. My
  recommendation is that you choose the MSI package and deal with the
  consequences if your system isn't equipped with support for the latest
  MS Installer; you'll be better off in the long run.  The build 623
  download is 7,460 KB, so now is a really good time to have some tea if
  you're on a slow dial-up connection.

  During installation, please ensure that you do choose the options to
  "Add Perl to the PATH environment variable" and "Create Perl file
  extension association"; it will make your life so much easier. Once
  the installation is finished, be sure to reboot your PC. You probably
  won't be told anywhere else that this needs to be done now, but it
  does. Really.

  Once you've rebooted, open a "DOS box" (Start > Run > command might do
  it, if you can't find it elsewhere) and from wherever it lands, type
  PERL -v <ENTER> (it's better if that's a lower-case be rewarded with
  some interesting information about your Perl installation. If you're
  not, you must go back to the beginning and discover what went wrong
  and fix it. It's pointless to proceed unless this simple check is
  passed. Assuming it did work, you may now move on.


  1.4.  Additional packages

  Some extensions ("packages") need to be added to the base Perl
  distribution, and we'll do this next. If you're using the Perl I
  recommended, and don't know any better for yourself, then just blindly
  following these instructions will work just fine. If that didn't
  describe you, then you're on your own.

  Visit the following URL:

  http://www.activestate.com/PPMPackages/zips/6xx-builds-only/

  and download the following files:-



       Data-Dumper.zip
       Net-Telnet.zip
       TimeDate.zip
       Time-HiRes.zip
       DB_File.zip




  Make yourself a convenient directory to unpack all of these zip files
  into (I put mine in "D:\ppm>") and do the following (the bits you type
  in are blue ). Note that where these files land will be directly
  related to where you chose to install your ActivePerl (mine, as you
  can probably guess from what follows, went into "D:\Perl"):-



       D:\ppm>ppm install Data-Dumper.ppd
       Installing package 'Data-Dumper.ppd'
       Installing D:\Perl\site\lib\auto\Data\Dumper\Dumper.bs
       Installing D:\Perl\site\lib\auto\Data\Dumper\Dumper.dll
       Installing D:\Perl\site\lib\auto\Data\Dumper\Dumper.exp
       Installing D:\Perl\site\lib\auto\Data\Dumper\Dumper.lib
       Installing D:\Perl\html\site\lib\auto\Data\Dumper\Dumper.html
       Installing D:\Perl\site\lib\Data\Dumper\Dumper.pm
       Writing D:\Perl\site\lib\auto\Data\Dumper\Dumper.packlist
       D:\ppm>




  I'm not going to bother you with exhaustive details of the rest of
  them, but suffice it to say you need to:



       ppm install DB_File.ppd
       ppm install Net-Telnet.ppd
       ppm install TimeDate.ppd
       ppm install Time-HiRes.ppd




  If all that seemed to work OK, time to move along. Before anyone who
  is familiar with PPM tells me that we didn't need to download and keep
  those files locally, I knew that. I also knew that PPM is sometimes
  awkward to configure via firewalls, and that sometimes the
  repositories don't always work the way we'd hope. I do it that way
  because it suits me.





  1.5.  Getting Spider

  Get the current version of the DX Spider distribution. This needs to
  be v1.47 or later. You've got two ways (currently) of getting this;
  either get a CVS update from sourceforge (if you don't know what this
  is, then it isn't for you) or get my package from:-

  http://www.dcc.rsgb.org/WinSpider.zip

  or if you want the lastest CVS version (which is produced every night)

  http://www.dxcluster.org/download/CVSlatest.tgz

  If you went down the CVS route, then everything will be nicely set out
  on your local disk. If you got the ZIP file, unpack it to somewhere
  convenient. The following examples assume that you put it on drive
  "C:\", for convenience.

  NOTE: This distribution method will go away as soon as the first v1.47
  tarball is released. You can use WinZip to unpack that, and my life
  will be made easier by not needing to keep this .ZIP file updated.


  2.  Installing the software

  Ensure that your CVS session or your unZIPped file have left you with
  a directory "C:\spider\local"; if not, go to "C:\spider\" and create
  one. If "C:\spider" is missing, go back and figure out why, because it
  shouldn't be.

  Now create your own local copy of the DXVars.pm file by:-



       copy c:\spider\perl\DXVars.pm.issue
       c:\spider\local\DXVars.pm




  Now you'll need to edit this file using a text editor. If nothing
  else, you can simply



       cd \spider\local




  and then



       notepad DXVars.pm




  to bring up an editor window containing the file. As an absolute
  minimum you must adjust the following items in DXVars.pm:-


  o  $mycall  - Should hold the callsign of your DX Cluster


  o  $myname  - The SysOp's first name

  o  $myalias - the SysOp's callsign. Cannot be the same as $mycall!

  You really also ought to update the $mylatitude, $mylongitude, $myqth
  and $myemail variables. And unless you are absolutely certain you know
  what you're doing, you should change nothing else in this file.


  2.1.  The AGW packet engine

  On the assumption that you'll be using the SV2AGW Packet Engine to
  interface your radios to the cluster, you should now create your own
  local copy of AGWConnect.pm by:-



       copy c:\spider\perl\AGWConnect.pm
       c:\spider\local\AGWConnect.pm




  and then



       notepad AGWConnect.pm




  to bring up an editor window containing the file. You must consider
  adjusting the following items in AGWConnect.pm:-


  o  $enable - set to '1' to enable AGWPE interface

  o  $login  - the login ID you chose when you set up the SV2AGW
     security :-)

  o  $passwd - password that matches $login


  2.2.  Setting up the initial user files

  Next you need to create the initial user files, etc. A tool is
  supplied which will do this for you. To run the tool:-



       cd \spider\perl
       perl create_sysop.pl




  If all goes according to plan, you will see no output from this
  program, and after a brief wait, your DOS prompt will be returned.

  Depending on how brave you are, you might now care to try the
  following:-




  perl cluster.pl




  If you did everything you were told, your DOS window will now hold a
  display which looks something like:-



       DXSpider DX Cluster Version 1.47
       Copyright (c) 1998-2001 Dirk Koopman G1TLH
       loading prefixes ...
       loading band data ...
       loading user file system ...
       starting listeners ...
       Internal port: localhost 27754
       load badwords: Ok
       reading in duplicate spot and WWV info ...
       reading existing message headers ...
       load badmsg: Ok
       load forward: Ok
       load swop: Ok
       @msg = 0 before delete
       @msg = 0 after delete
       reading cron jobs ...v cron: reading /spider/cmd/crontab
       cron: adding 1 0 * * 0
       DXUser::export("$main::data/user_asc")
       reading database descriptors ...
       doing local initialisation ...
       orft we jolly well go ...
       queue msg (0)




  Now, if that's what you've got, you are very nearly home and dry (in
  as far as these particular experiments are concerned, anyhow)

  To access your new cluster (from the local machine) find yourself
  another "DOS box" and do the following:-



       cd \spider\perl
       perl winclient.pl




  If you are rewarded with a display which looks something like:-



       Hello Iain, this is GB7SJP in Amersham, Bucks running DXSpider V1.47
       Cluster: 1 nodes, 1 local / 1 total users Max users 2 Uptime 0 00:00
       M0ADI de GB7SJP 4-Mar-2001 1511Z >




  You've arrived. Try some commands, and see how they feel. (In case you
  were wondering, "Iain", "M0ADI" and "GB7SJP" all came from the version
  of DXVars.pm that was on the machine when I started the winclient.pl)


  2.3.  Incoming telnets

  If you want to enable inbound "TELNET" connections, you've got a
  little more work to do. From a handy "DOS box" that's not doing
  anything else, do the following:-



       copy \spider\perl\listeners.pm \spider\local
       cd \spider\local
       notepad listeners.pm




  The following lines need attention:-



       ["0.0.0.0", 7300],




  On my machine, I've simply uncommented the "0.0.0.0" entry by removing
  the '#' from the front of the line.

  If you don't have a static hostname for your machine, and you intend
  to allow folk to connect to your machine across the internet, then I'd
  suggest you pay a visit to www.dyndns.org and create one for yourself.
  While it's free, it will take a modest an amount of effort on your
  part to read, understand and implement what needs to be done to set
  this up.


  2.4.  Connecting to other clusters

  If you want to connect this to another cluster, then you'll want to
  negotiate a link with someone. For experimental purposes, I'm happy to
  allow folk to connect to GB7DXA (spud.ath.cx), on the understanding
  that the system may or may not be there and may or may not be
  connected to anything particularly useful at any given moment. Contact
  me by Email if you want me to set up a connection for you.

  Last updated: 15-Apr-01