1 <!doctype linuxdoc system>
\r
5 <!-- Title information -->
\r
7 <title>The DXSpider Administration Manual v1.50</title>
\r
8 <author>Ian Maude, G0VGS, (g0vgs@gb7mbc.net), and
\r
9 Charlie Carroll, K1XX, (k1xx@ptcnh.net)</author>
\r
10 <date>March 2003 revision 0.5</date>
\r
13 A reference for SysOps of the DXSpider DXCluster program.
\r
16 <!-- Table of contents -->
\r
19 <!-- Begin the document -->
\r
21 <sect>Routing and Filtering
\r
26 From DXSpider version 1.48, major changes were introduced to the way
\r
27 node connections are treated. This is part of an ongoing process to
\r
28 remove problems with loops and to enable talk and other functions to
\r
29 propagate across the whole of the worldwide cluster network. In fact,
\r
30 in a Spider network, it would be useful, perhaps even necessary to
\r
31 have loops. This would give real resilience to the network, meaning
\r
32 that if a link dropped, the information flow would simply come in and
\r
33 go out via a different route. Of course, we do not have a complete
\r
34 network of Spider nodes, there are other programs out there. Some of
\r
35 these do not have any protection from loops. Certainly AK1A does not
\r
36 handle loops well at all. It is therefore necessary to have some form
\r
37 of protection for these nodes.
\r
40 In fact DXSpider has had a simple system for some time which is called
\r
41 <it>isolation</it>. This is similar to what in other systems such as
\r
42 <bf>clx</bf>, is called <it>passive mode</it>. A more detailed explanation
\r
43 of <it>isolation</it> is given further below. This system is still available
\r
44 and, for simple networks, is probably all that you need.
\r
47 The new functionality introduced in version 1.48 allows filtering the node
\r
48 and user protocol frames on a "per interface" basis. We call this
\r
49 <it>route filtering</it>. This is used <bf>instead of</bf>
\r
50 <it>isolation</it>.
\r
53 What this really means is that you can control more or less completely
\r
54 which user and node management PC protocol frames pass to each of your
\r
55 partner nodes. You can also limit what comes into your node from your
\r
56 partners. It is even possible to control the settings that your partner
\r
57 node has for the routing information that it sends to you
\r
58 (using the <it>rcmd</it> command).
\r
60 <sect1>Route Filters
\r
63 Initially when route filters were being tested we generated a
\r
64 "default" filter. Unfortunately it quickly became apparent that this
\r
65 might suit the UK cluster network but didn't really fit anybody else.
\r
66 However using a default filter is an appropriate thing to do. How, is
\r
67 explained further on.
\r
70 The first thing that you must do is determine whether you need to use
\r
71 route filtering <bf>at all</bf>. If you are a "normal" node with two or
\r
72 three partners and you arranged in an "official" non-looping tree type
\r
73 network, then <bf>you do not need to do route filtering</bf> and you will
\r
74 feel a lot better for not getting involved. If you are successfully using
\r
75 <it>isolation</it> then you also probably don't need to use route filtering.
\r
78 To put it simply, you should not mix Isolation and Route Filtering. It
\r
79 will work, of sorts, but you will not get the expected results. If you
\r
80 are using Isolation sucessfully at the moment, do not get involved in
\r
81 Route Filtering unless you have a good supply of aspirin! Once you have
\r
82 started down the road of Route Filtering, do not use Isolation either.
\r
83 Use one or the other, not both.
\r
86 You will only require this functionality if you are "well-connected". What
\r
87 that means is that you are connected to several different parts of (say)
\r
88 the EU cluster and, at the same time, also connected to two or three places
\r
89 in the US which, in turn are connected back to the EU. This is called a
\r
90 "loop" and if you are seriously looped then you need filtering.
\r
93 I should at this stage give a little bit of background on filters. All
\r
94 the filters in Spider work in basically the same way. You can either
\r
95 accept or reject various options in order to create the filter rules
\r
96 you wish to achieve. Some filters are user settable, others can only
\r
97 be altered by the sysop. Route filtering can only be done by the sysop.
\r
100 Anyway, without further discouragement, let me start the process
\r
103 <sect1>The node_default filter
\r
106 All normal systems should have a default routing filter and it should
\r
107 usually be set to send only the normal, unlooped, view of your
\r
108 "national" network. Here in the UK that means nodes from the UK and
\r
109 Eire, in EU it is more complex as the networks there grew up in a more
\r
113 The generic commands are:-
\r
116 reject/route node_default <filter_option>
\r
120 accept/route node_default <filter_option>
\r
123 where filter_option is one of the following ...
\r
126 call <prefixes>
\r
127 call_dxcc <numbers>
\r
128 call_itu <numbers>
\r
129 call_zone <numbers>
\r
130 channel <prefixes>
\r
131 channel_dxcc <numbers>
\r
132 channel_itu <numbers>
\r
133 channel_zone <numbers>
\r
136 Please be careful if you alter this setting, it will affect
\r
137 <bf><it>ALL</it></bf> your links! Remember, this is a <it>default</it>
\r
138 filter for node connections, not a <it>per link</it> default.
\r
141 For the default routing filter then you have two real choices: either
\r
142 a "national" view or the "safe" option of only your own
\r
143 callsign. Examples of each (for my node: GB7DJK) are:-
\r
146 acc/route node_default call_dxcc 61,38
\r
147 acc/route node_default call gb7djk
\r
150 GB7DJK uses the first of these. The DXCC countries can be obtained from the
\r
151 <it>show/prefix</it> command.
\r
154 The example filters shown control <it>output</it> <bf>TO</bf> all your
\r
155 partner nodes unless they have a specific filter applied to them (see
\r
159 It is also possible to control the <it>incoming</it> routing
\r
160 information that you are prepared to accept <bf>FROM</bf> your partner
\r
161 nodes. The reason this is necessary is to make sure that stuff like
\r
162 mail, pings and similar commands a) go down the correct links and b)
\r
163 don't loop around excessively. Again using GB7DJK as an example a typical
\r
164 default input filter would be something like:
\r
167 rej/route node_default input call_dxcc 61,38 and not channel_dxcc 61,38
\r
170 What this does is accept node and user information for our national
\r
171 network from nodes that are in our national network, but rejects such
\r
172 information from anyone else. Although it doesn't explicitly say so,
\r
173 by implication, any other node information (not from the UK and Eire)
\r
177 As I imagine it will take a little while to get one's head around all of
\r
178 this you can study the effect of any rules that you try by watching the
\r
179 debug output after having done:-
\r
185 After you have got tired of that, to put it back the way it was:-
\r
191 <sect1>General route filtering
\r
194 Exactly the same rules apply for general route filtering. You would
\r
195 use either an accept filter or a reject filter like this ...
\r
198 reject/route <node_call> <filter_option>
\r
202 accept/route <node_call> <filter_option>
\r
206 Here are some examples of route filters ...
\r
209 rej/route gb7djk call_dxcc 61,38 (send everything except UK+EIRE nodes)
\r
210 rej/route all (equiv to [very] restricted mode)
\r
211 acc/route gb7djk call_dxcc 61,38 (send only UK+EIRE nodes)
\r
212 acc/route gb7djk call gb7djk (equiv to SET/ISOLATE)
\r
215 In practice you will either be opening the default filter out for a
\r
216 partner by defining a specific filter for that callsign:-
\r
219 acc/route gb7baa all
\r
220 acc/route gb7baa input all
\r
223 or restricting it quite a lot, in fact making it very nearly like an
\r
224 <it>isolated</it> node, like this:-
\r
227 acc/route pi4ehv-8 call gb7djk
\r
228 rej/route pi4ehv-8 input call_dxcc 61,38
\r
231 This last example takes everything except UK and Eire from PI4EHV-8
\r
232 but only sends him my local configuration (just a PC19 for GB7DJK and
\r
233 PC16s for my local users).
\r
236 It is possible to write <bf>much</bf> more complex rules, there are up
\r
237 to 10 accept/reject pairs per callsign per filter. For more information
\r
238 see the next section.
\r
241 <sect1>General filter rules
\r
244 Upto v1.44 it was not possible for the user to set their own filters. From
\r
245 v1.45 though that has all changed. It is now possible to set filters for just
\r
246 about anything you wish. If you have just updated from an older version of
\r
247 DXSpider you will need to update your new filters. You do not need to do
\r
248 anything with your old filters, they will be renamed as you update.
\r
251 There are 3 basic commands involved in setting and manipulating filters. These
\r
252 are <em>accept</em>, <em>reject</em> and <em>clear</em>. First we will look
\r
253 generally at filtering. There are a number of things you can filter in the
\r
254 DXSpider system. They all use the same general mechanism.
\r
257 In general terms you can create a "reject" or an "accept" filter which can have
\r
258 up to 10 lines in it. You do this using, for example ...
\r
265 where ..... are the specific commands for that type of filter. There are filters
\r
266 for spots, wwv, announce, wcy and (for sysops) connects. See each different
\r
267 accept or reject command reference for more details.
\r
269 There is also a command to clear out one or more lines in a filter. They are ...
\r
276 There is clear/xxxx command for each type of filter.
\r
279 and you can check that your filters have worked by the command ...
\r
286 For now we are going to use spots for the examples, but you can apply the same
\r
287 principles to all types of filter.
\r
289 <sect1>Types of filter
\r
292 There are two main types of filter, <em>accept</em> or <em>reject</em>. You
\r
293 can use either to achieve the result you want dependent on your own preference
\r
294 and which is more simple to do. It is pointless writing 8 lines of reject
\r
295 filters when 1 accept filter would do the same thing! Each filter has 10
\r
296 lines (of any length) which are tried in order. If a line matches then the
\r
297 action you have specified is taken (ie reject means ignore it and accept
\r
301 If you specify reject filters, then any lines that arrive that match the filter
\r
302 will be dumped but all else will be accepted. If you use an accept filter,
\r
303 then ONLY the lines in the filter will be accepted and all else will be dumped.
\r
304 For example if you have a single line <em>accept</em> filter ...
\r
307 accept/spots on vhf and (by_zone 14,15,16 or call_zone 14,15,16)
\r
310 then you will <em>ONLY</em> get VHF spots <em>from</em> or <em>to</em> CQ zones
\r
314 If you set a reject filter like this ...
\r
317 reject/spots on hf/cw
\r
320 Then you will get everything <em>EXCEPT</em> HF CW spots. You could make this
\r
321 single filter even more flexible. For example, if you are interested in IOTA
\r
322 and will work it even on CW even though normally you are not interested in
\r
323 CW, then you could say ...
\r
326 reject/spots on hf/cw and not info iota
\r
329 But in that case you might only be interested in iota and say:-
\r
332 accept/spots not on hf/cw or info iota
\r
335 which achieves exactly the same thing. You should choose one or the other
\r
336 until you are comfortable with the way it works. You can mix them if you
\r
337 wish (actually you can have an accept AND a reject on the same line) but
\r
338 don't attempt this until you are sure you know what you are doing!
\r
341 You can arrange your filter lines into logical units, either for your own
\r
342 understanding or simply convenience. Here is an example ...
\r
345 reject/spots 1 on hf/cw
\r
346 reject/spots 2 on 50000/1400000 not (by_zone 14,15,16 or call_zone 14,15,16)
\r
349 What this does is to ignore all HF CW spots and also rejects any spots on VHF
\r
350 which don't either originate or spot someone in Europe.
\r
353 This is an example where you would use a line number (1 and 2 in this case), if
\r
354 you leave the digit out, the system assumes '1'. Digits '0'-'9' are available.
\r
355 This make it easier to see just what filters you have set. It also makes it
\r
356 more simple to remove individual filters, during a contest for example.
\r
359 You will notice in the above example that the second line has brackets. Look
\r
360 at the line logically. You can see there are 2 separate sections to it. We
\r
361 are saying reject spots that are VHF or above <em>APART</em> from those in
\r
362 zones 14, 15 and 16 (either spotted there or originated there). If you did
\r
363 not have the brackets to separate the 2 sections, then Spider would read it
\r
364 logically from the front and see a different expression entirely ...
\r
367 (on 50000/1400000 and by_zone 14,15,16) or call_zone 14,15,16
\r
370 The simple way to remember this is, if you use OR - use brackets. Whilst we are
\r
371 here CASE is not important. 'And BY_Zone' is just the same as 'and by_zone'.
\r
373 As mentioned earlier, setting several filters can be more flexible than
\r
374 simply setting one complex one. Doing it in this way means that if you want
\r
375 to alter your filter you can just redefine or remove one or more lines of it or
\r
376 one line. For example ...
\r
379 reject/spots 1 on hf/ssb
\r
382 would redefine our earlier example, or
\r
388 To remove all the filter lines in the spot filter ...
\r
394 <sect1>Filter options
\r
397 You can filter in several different ways. The options are listed in the
\r
398 various helpfiles for accept, reject and filter.
\r
400 <sect1>Default filters
\r
403 Sometimes all that is needed is a general rule for node connects. This can
\r
404 be done with a node_default filter. This rule will always be followed, even
\r
405 if the link is isolated, unless another filter is set specifically. Default
\r
406 rules can be set for nodes and users. They can be set for spots, announces,
\r
407 WWV and WCY. They can also be used for hops. An example might look like
\r
411 accept/spot node_default by_zone 14,15,16,20,33
\r
412 set/hops node_default spot 50
\r
415 This filter is for spots only, you could set others for announce, WWV and WCY.
\r
416 This filter would work for ALL nodes unless a specific filter is written to
\r
417 override it for a particular node. You can also set a user_default should
\r
418 you require. It is important to note that default filters should be
\r
419 considered to be "connected". By this I mean that should you override the
\r
420 default filter for spots, you need to add a rule for the hops for spots also.
\r
422 <sect1>Advanced filtering
\r
425 Once you are happy with the results you get, you may like to experiment.
\r
428 The previous example that filters hf/cw spots and accepts vhf/uhf spots from EU
\r
429 can be written with a mixed filter, for example ...
\r
433 acc/spot on 0/30000
\r
434 acc/spot 2 on 50000/1400000 and (by_zone 14,15,16 or call_zone 14,15,16)
\r
437 Note that the first filter has not been specified with a number. This will
\r
438 automatically be assumed to be number 1. In this case, we have said <em>reject all
\r
439 HF spots in the CW section of the bands but accept all others at HF. Also
\r
440 accept anything in VHF and above spotted in or by operators in the zones
\r
441 14, 15 and 16</em>. Each filter slot actually has a 'reject' slot and
\r
442 an 'accept' slot. The reject slot is executed BEFORE the accept slot.
\r
445 It was mentioned earlier that after a reject test that doesn't match, the default
\r
446 for following tests is 'accept', the reverse is true for 'accept'. In the example
\r
447 what happens is that the reject is executed first, any non hf/cw spot is passed
\r
448 to the accept line, which lets through everything else on HF. The next filter line
\r
449 lets through just VHF/UHF spots from EU.
\r
451 <sect1>Basic hop control
\r
454 In /spider/data you will find a file called hop_table.pl. This is the file
\r
455 that controls your hop count settings. It has a set of default hops on the
\r
456 various PC frames and also a set for each node you want to alter the hops for.
\r
457 You may be happy with the default settings of course, but this powerful tool
\r
458 can help to protect and improve the network. The file will look something
\r
463 # hop table construction
\r
468 # default hopcount to use
\r
471 # some variable hop counts based on message type
\r
482 # the per node hop control thingy
\r
487 GB7ADX => { 11 => 8,
\r
495 GB7UDX => { 11 => 8,
\r
514 Each set of hops is contained within a pair of curly braces and contains a
\r
515 series of PC frame types. PC11 for example is a DX spot. The figures here
\r
516 are not exhaustive but should give you a good idea of how the file works.
\r
519 SHould any of the nodecalls include an ssid, it is important to wrap the
\r
520 whole call in single quotes, like this ...
\r
533 If you do not do this, you will get errors and the file will not work as
\r
537 You can alter this file at any time, including whilst the cluster is running.
\r
538 If you alter the file during runtime, the command <em>load/hops</em> will
\r
539 bring your changes into effect.
\r
541 <sect1>Hop Control on Specific Nodes
\r
543 <p>You can set a callsign specific hop count for any of the standard filter
\r
547 set/hops gb7djk spot 4
\r
548 set/hops node_default route 10
\r
549 set/hops gb7baa wcy 5
\r
552 all work on their specific area of the protocol.
\r
555 The <em>set/hops</em> command overrides any hops that you have set otherwise.
\r
558 You can show what hops have been set using the <em>show/hops</em> command.
\r
560 <sect1>Isolating networks
\r
563 It is possible to isolate networks from each other on a "gateway" node using the
\r
564 <em>set/isolate <node_call></em> command.
\r
567 The effect of this is to partition an isolated network completely from another
\r
568 node connected to your node. Your node will appear on and otherwise behave
\r
569 normally on every network to which you are connected, but data from an isolated
\r
570 network will not cross onto any other network or vice versa. However all the
\r
571 spot, announce and WWV traffic and personal messages will still be handled
\r
572 locally (because you are a real node on all connected networks), that is locally
\r
573 connected users will appear on all networks and will be able to access and
\r
574 receive information from all networks transparently. All routed messages will
\r
575 be sent as normal, so if a user on one network knows that you are a gateway for
\r
576 another network, he can still still send a talk/announce etc message via your
\r
577 node and it will be routed across.
\r
580 If you use isolate on a node connection you will continue to receive
\r
581 all information from the isolated partner, however you will not pass
\r
582 any information back to the isolated node. There are times when you
\r
583 would like to forward only spots across a link (maybe during a contest
\r
584 for example). To do this, isolate the node in the normal way and use
\r
585 an <em>acc/spot >call< all</em> filter to override the isolate.
\r
587 <sect>Other filters
\r
589 <sect1>Filtering Mail
\r
592 In the /spider/msg directory you will find a file called badmsg.pl.issue. Rename
\r
593 this to badmsg.pl and edit the file. The original looks something like this ....
\r
597 # the list of regexes for messages that we won't store having
\r
598 # received them (bear in mind that we must receive them fully before
\r
602 # The format of each line is as follows
\r
604 # type source pattern
\r
605 # P/B/F T/F/O/S regex
\r
607 # type: P - private, B - bulletin (msg), F - file (ak1a bull)
\r
608 # source: T - to field, F - from field, O - origin, S - subject
\r
609 # pattern: a perl regex on the field requested
\r
611 # Currently only type B and P msgs are affected by this code.
\r
613 # The list is read from the top down, the first pattern that matches
\r
614 # causes the action to be taken.
\r
616 # The pattern can be undef or 0 in which case it will always be selected
\r
617 # for the action specified
\r
625 'B', 'T', 'WANTED',
\r
626 'B', 'S', 'WANTED',
\r
635 I think this is fairly self explanatory. It is simply a list of subject
\r
636 headers that we do not want to pass on to either the users of the cluster or
\r
637 the other cluster nodes that we are linked to. This is usually because of
\r
638 rules and regulations pertaining to items for sale etc in a particular country.
\r
641 <sect1>Filtering words from text fields in Announce, Talk and DX spots
\r
644 From version 1.48 onwards the interface to this has changed. You can now
\r
645 use the commands <em>set/badword</em> to add words that you are not prepared
\r
646 to see on the cluster, <em>unset/badword</em> to allow that word again and
\r
647 <em>show/badword</em> to list the words that you have set.
\r
650 If you have a previous <em>/spider/data/badwords</em>, the first time you start
\r
651 the node, it will read and convert this file to the new commands. The old style
\r
652 file will then be removed.
\r
654 <sect1>Stopping (possibly bad) DX Spots from Nodes or Spotters
\r
657 There are a number of commands that control whether a spot progresses
\r
658 any further by regarding it as "bad" in some way.
\r
661 A DX Spot has a number of fields which can be checked to see whether they
\r
662 contain "bad" values, they are: the DX callsign itself, the Spotter and
\r
663 the Originating Node.
\r
666 There are a set of commands which allow the sysop to control whether a
\r
675 These work in the same as the <em>set/badword</em> command, you can add
\r
676 any words or callsigns or whatever to the appropriate database. For
\r
677 example, to stop a spot from a particular node you do:
\r
680 set/badnode gb7djk gb7dxc
\r
686 set/badspotter b0mb p1rat nocall
\r
692 set/baddx video wsjt
\r
695 You can remove a word using the appropriate unset command
\r
696 (<em>unset/baddx, unset/badspotter, unset/badnode</em>) or list them
\r
697 using one of <em>show/baddx, show/badspotter</em> and
\r
698 <em>show/badnode</em>.
\r
703 DXSpider deals seamlessly with standard AK1A type mail. It supports both
\r
704 personal and bulletin mail and the sysop has additional commands to ensure
\r
705 that mail gets to where it is meant. DXSpider will send mail almost
\r
706 immediately, assuming that the target is on line. However, only one
\r
707 mail message is dealt with at any one time. If a mail message is already
\r
708 being sent or recieved, then the new message will be queued until it has
\r
711 The cluster mail is automatically deleted after 30 days unless the sysop
\r
712 sets the "keep" flag using the <em>msg</em> command.
\r
714 <sect1>Personal mail
\r
717 Personal mail is sent using the <em>sp</em> command. This is actually the
\r
718 default method of sending mail and so a simple <em>s</em> for send will do.
\r
719 A full list of the send commands and options is in the <em>command set</em>
\r
720 section, so I will not duplicate them here.
\r
722 <sect1>Bulletin mail
\r
725 Bulletin mail is sent by using the <em>sb</em> command. This is one of the
\r
726 most common mistakes users make when sending mail. They send a bulletin
\r
727 mail with <em>s</em> or <em>sp</em> instead of <em>sb</em> and of course
\r
728 the message never leaves the cluster. This can be rectified by the sysop
\r
729 by using the <em>msg</em> command.
\r
731 <P>Bulletin addresses can be set using the Forward.pl file.
\r
736 DXSpider receives all and any mail sent to it without any alterations needed
\r
737 in files. Because personal and bulletin mail are treated differently, there
\r
738 is no need for a list of accepted bulletin addresses. It is necessary, however,
\r
739 to tell the program which links accept which bulletins. For example, it is
\r
740 pointless sending bulletins addresses to "UK" to any links other than UK
\r
741 ones. The file that does this is called forward.pl and lives in /spider/msg.
\r
742 At default, like other spider files it is named forward.pl.issue. Rename it
\r
743 to forward.pl and edit the file to match your requirements.
\r
744 The format is below ...
\r
748 # this is an example message forwarding file for the system
\r
750 # The format of each line is as follows
\r
752 # type to/from/at pattern action destinations
\r
753 # P/B/F T/F/A regex I/F [ call [, call ...] ]
\r
755 # type: P - private, B - bulletin (msg), F - file (ak1a bull)
\r
756 # to/from/at: T - to field, F - from field, A - home bbs, O - origin
\r
757 # pattern: a perl regex on the field requested
\r
758 # action: I - ignore, F - forward
\r
759 # destinations: a reference to an array containing node callsigns
\r
761 # if it is non-private and isn't in here then it won't get forwarded
\r
763 # Currently only type B msgs are affected by this code.
\r
765 # The list is read from the top down, the first pattern that matches
\r
766 # causes the action to be taken.
\r
768 # The pattern can be undef or 0 in which case it will always be selected
\r
769 # for the action specified
\r
771 # If the BBS list is undef or 0 and the action is 'F' (and it matches the
\r
772 # pattern) then it will always be forwarded to every node that doesn't have
\r
773 # it (I strongly recommend you don't use this unless you REALLY mean it, if
\r
774 # you allow a new link with this on EVERY bull will be forwarded immediately
\r
775 # on first connection)
\r
781 'B', 'T', 'LOCAL', 'F', [ qw(GB7MBC) ],
\r
782 'B', 'T', 'ALL', 'F', [ qw(GB7BAA GB7ADX PA4AB-14) ],
\r
783 'B', 'T', 'UK', 'F', [ qw(GB7BAA GB7ADX) ],
\r
784 'B', 'T', 'QSL', 'F', [ qw(GB7BAA GB7ADX PA4AB-14) ],
\r
785 'B', 'T', 'QSLINF', 'F', [ qw(GB7BAA GB7ADX PA4AB-14) ],
\r
786 'B', 'T', 'DX', 'F', [ qw(GB7BAA GB7ADX PA4AB-14) ],
\r
787 'B', 'T', 'DXINFO', 'F', [ qw(GB7BAA GB7ADX PA4AB-14) ],
\r
788 'B', 'T', 'DXNEWS', 'F', [ qw(GB7BAA GB7ADX PA4AB-14) ],
\r
789 'B', 'T', 'DXQSL', 'F', [ qw(GB7BAA GB7ADX PA4AB-14) ],
\r
790 'B', 'T', 'SYSOP', 'F', [ qw(GB7BAA GB7ADX) ],
\r
791 'B', 'T', '50MHZ', 'F', [ qw(GB7BAA GB7ADX PA4AB-14) ],
\r
795 Simply insert a bulletin address and state in the brackets where you wish
\r
796 that mail to go. For example, you can see here that mail sent to "UK" will
\r
797 only be sent to the UK links and not to PA4AB-14.
\r
800 To force the cluster to reread the file use load/forward
\r
803 NB: If a user tries to send mail to a bulletin address that does not exist
\r
804 in this file, they will get an error.
\r
806 <sect1>The msg command
\r
809 The <em>msg</em> command is a very powerful and flexible tool for the
\r
810 sysop. It allows the sysop to alter to and from fields and make other
\r
811 changes to manage the cluster mail.
\r
813 Here is a full list of the various options ...
\r
816 MSG TO <msgno> <call> - change TO callsign to <call>
\r
817 MSG FRom <msgno> <call> - change FROM callsign to <call>
\r
818 MSG PRrivate <msgno> - set private flag
\r
819 MSG NOPRrivate <msgno> - unset private flag
\r
820 MSG RR <msgno> - set RR flag
\r
821 MSG NORR <msgno> - unset RR flag
\r
822 MSG KEep <msgno> - set the keep flag (message won't be deleted ever)
\r
823 MSG NOKEep <msgno> - unset the keep flag
\r
824 MSG SUbject <msgno> <new> - change the subject to <new>
\r
825 MSG WAittime <msgno> - remove any waiting time for this message
\r
826 MSG NOREad <msgno> - mark message as unread
\r
827 MSG REad <msgno> - mark message as read
\r
828 MSG QUeue - queue any outstanding bulletins
\r
829 MSG QUeue 1 - queue any outstanding private messages
\r
832 These commands are simply typed from within the cluster as the sysop user.
\r
834 <sect1>Message status
\r
837 You can check on a message from within the cluster by using the command
\r
838 <em>stat/msg</em>. This will give you additional information on the
\r
839 message number including which nodes have received it, which node it
\r
840 was received from and when etc. Here is an example of the output of
\r
844 G0VGS de GB7MBC 28-Jan-2001 1308Z >
\r
847 Msg Time: 26-Jan-2001 1302Z
\r
851 Subject: AMSAT 2line KEPS 01025.AMSAT
\r
853 Got it Nodes: GB7BAA, GB7ADX
\r
857 G0VGS de GB7MBC 28-Jan-2001 1308Z >
\r
860 <sect1>Filtering mail
\r
863 This is described in the section on <em>Other filters</em> so I will not
\r
866 <sect1>Distribution lists
\r
869 Distribution lists are simply a list of users to send certain types of
\r
870 mail to. An example of this is mail you only wish to send to other
\r
871 sysops. In /spider/msg there is a directory called <em>distro</em>. You
\r
872 put any distibution lists in here. For example, here is a file called
\r
873 SYSOP.pl that caters for the UK sysops.
\r
876 qw(GB7TLH GB7DJK GB7DXM GB7CDX GB7BPQ GB7DXN GB7MBC GB7MBC-6 GB7MDX
\r
877 GB7NDX GB7SDX GB7TDX GB7UDX GB7YDX GB7ADX GB7BAA GB7DXA GB7DXH
\r
878 GB7DXK GB7DXI GB7DXS)
\r
881 Any mail sent to "sysop" would only be sent to the callsigns in this list.
\r
883 <sect1>BBS interface
\r
886 Spider provides a simple BBS interface. No input is required from the sysop
\r
887 of the cluster at all. The BBS simply sets the cluster as a BBS and pushes
\r
888 any required mail to the cluster. No mail can flow from Spider to the BBS,
\r
889 the interface is one-way.
\r
892 Please be careful not to flood the cluster network with unnecessary mail.
\r
893 Make sure you only send mail to the clusters that want it by using the
\r
894 Forward.pl file very carefully.
\r
899 From 1.48 onwards it will become increasingly possible to control DXSpider's
\r
900 operation with scripts of various kinds.
\r
903 The directory /spider/scripts is where it all happens and is used for several
\r
904 things. Firstly it contains a file called startup that can be used to call
\r
905 in any changes to the cluster from the default settings on startup. This
\r
906 script is executed immediately after all initialisation of the node is done
\r
907 but before any connections are possible. Examples of this include how many
\r
908 spots it is possible to get with the sh/dx command, whether you want
\r
909 registration/passwords to be permanently on etc. An example file is shown
\r
910 below and is included in the distribution as startup.issue.
\r
914 # startup script example
\r
916 # set maximum no of spots allowed to 100
\r
917 # set/var $Spot::maxspots = 100
\r
919 # Set registration on
\r
920 # set/var $main::reqreg = 1
\r
923 # set/var $main::passwdreq = 1
\r
928 As usual, any text behind a # is treated as a comment and not read. To use
\r
929 this file, simply rename it from startup.issue to startup. In our example
\r
930 above there are three options. The first option is the amount of spots that
\r
931 a user can request with the <em>sh/dx</em> command. Normally the default is
\r
932 to give 10 spots unless the user specifies more. Without this line enabled,
\r
933 the maximum a user can request is 100 spots. Depending on your link quality
\r
934 you may wish to enable more or less by specifying the number.
\r
937 The other 2 options are dealt with more fully in the security section.
\r
940 Secondly, it is used to store the login scripts for users and nodes. Currently
\r
941 this can only be done by the sysop but it is envisaged that eventually users will
\r
942 be able to set their own. An example is included in the distibution but here is
\r
958 The lines in between commands can simply insert a blank line or a character
\r
959 such as a + sign to make the output easier to read. Simply create this script
\r
960 with your favourite editor and save it with the callsign of the user as the
\r
961 filename. Filenames should always be in lower case.
\r
964 Commands can be inserted in the same way for nodes. A node may wish a series
\r
965 of commands to be issued on login, such as a merge command for example.
\r
968 Thirdly, there are 2 default scripts for users and nodes who do not have a
\r
969 specifically defined script. These are <em>user_default</em> and
\r
970 <em>node_default</em>
\r
975 Spider allows the creation of local or remote databases. It supports
\r
976 chained databases, allowing several different databases to be scanned
\r
977 with one simple command. Importing of databases is limited at present
\r
978 to the standard AK1A databases such as OBLAST and the DB0SDX QSL
\r
979 database but will expand with time.
\r
981 <sect1>Creating databases
\r
984 Creating a database could not be more simple. All the commands are
\r
985 sent from the cluster prompt as the <em>sysop</em> user.
\r
987 To create a database you use the command <em>dbcreate</em>. It can
\r
988 be used in 3 different ways like so ..
\r
994 To simply create a database locally, you just tell the command the
\r
995 name of the database. This does not create the actual database, it
\r
996 simply defines it to say that it exists.
\r
999 dbcreate <name> chain <name> [<name>...]
\r
1002 This creates a chained database entry. The first database will be
\r
1003 scanned, then the second, the third etc...
\r
1006 dbcreate <name> remote <name>
\r
1009 This creates a remote entry. the first name field is the database
\r
1010 name at the remote node, then the remote switch, then the actual
\r
1011 node_call of the remote node, for example...
\r
1014 dbcreate buckmaster remote gb7dxc
\r
1017 Remote databases cannot be chained, however, the last database in a
\r
1018 chain can be a remote database.
\r
1020 <sect1>Importing databases
\r
1023 The only databases that Spider can currently import are the standard
\r
1024 AK1A databases such as OBLAST or the DB0SDX qsl and address database.
\r
1025 This will be added to with time.
\r
1027 To import such a database, first put the file somewhere useful like /tmp
\r
1028 and then issue the following command ...
\r
1031 dbimport oblast /tmp/OBLAST.FUL
\r
1034 This will update the existing local oblast database or create it if
\r
1035 it does not exist.
\r
1037 <sect1>Checking available databases
\r
1040 Once a database is created, you will want to check that it has been
\r
1041 added. To do this use the <em>dbavail</em> command. This will
\r
1042 output the available databases. For example ...
\r
1046 DB Name Location Chain
\r
1050 G0VGS de GB7MBC 3-Feb-2001 1925Z >
\r
1053 <sect1>Looking up databases
\r
1056 To look for information in a defined database, simply use the <em>dbshow</em>
\r
1057 command, for example ...
\r
1060 dbshow buckmaster G0YLM
\r
1063 will show the information for the callsign G0YLM from the buckmaster
\r
1064 database if it exists. To make things more standard for the users
\r
1065 you can add an entry in the Aliases file so that it looks like a standard
\r
1066 <em>show</em> command like this ...
\r
1069 '^sh\w*/buc', 'dbshow buckmaster', 'dbshow',
\r
1072 Now you can simply use show/buckmaster or an abreviation.
\r
1074 <sect1>Removing databases
\r
1077 To delete an existing database you use the <em>dbremove</em> command.
\r
1084 would remove the oblast database and its associated datafile from the
\r
1085 system. There are no warnings or recovery possible from this command.
\r
1086 If you remove a database it ceases to exist and would have to be created
\r
1087 from scratch if you still required it.
\r
1089 <sect>Information, files and useful programs
\r
1094 One of the more important things a cluster sysop needs to do is to get
\r
1095 information to his users. The simplest way to do this is to have a banner
\r
1096 that is sent to the user on login. This is know as a "message of the day"
\r
1097 or "motd". To set this up, simply create a file in /spider/data called motd
\r
1098 and edit it to say whatever you want. It is purely a text file and will be
\r
1099 sent automatically to anyone logging in to the cluster.
\r
1104 This message of the day file lives in the same directory as the standard
\r
1105 motd file but is only sent to non-registered users. Once registered they
\r
1106 will receive the same message as any other user.
\r
1108 <sect1>Downtime message
\r
1111 If for any reason the cluster is down, maybe for upgrade or maintenance but
\r
1112 the machine is still running, a message can be sent to the user advising them
\r
1113 of the fact. This message lives in the /spider/data directory and is called
\r
1114 "offline". Simply create the file and edit it to say whatever you wish.
\r
1115 This file will be sent to a user attempting to log into the cluster when
\r
1116 DXSpider is not actually running.
\r
1118 <sect1>Other text messages
\r
1121 You can set other text messages to be read by the user if they input the file
\r
1122 name. This could be for news items or maybe information for new users.
\r
1123 To set this up, make a directory under /spider called <em>packclus</em>.
\r
1124 Under this directory you can create files called <em>news</em> or <em>newuser</em>
\r
1125 for example. In fact you can create files with any names you like. These can
\r
1126 be listed by the user with the command ....
\r
1132 They can be read by the user by typing the command ....
\r
1138 If the file they want to read is called <em>news</em>. You could also set
\r
1139 an alias for this in the Alias file to allow them just to type <em>news</em>
\r
1142 You can also store other information in this directory, either directly or
\r
1143 nested under directories. One use for this would be to store DX bulletins
\r
1144 such as the OPDX bulletins. These can be listed and read by the user.
\r
1145 To keep things tidy, make a directory under /spider/packclus called
\r
1146 <em>bulletin</em>. Now copy any OPDX or similar bulletins into it. These
\r
1147 can be listed by the user in the same way as above using the <em>show/files</em>
\r
1148 command with an extension for the bulletin directory you have just created,
\r
1152 show/files bulletin
\r
1156 An example would look like this ....
\r
1160 bulletin DIR 20-Dec-1999 1715Z news 1602 14-Dec-1999 1330Z
\r
1163 You can see that in the files area (basically the packclus directory) there is a
\r
1164 file called <em>news</em> and a directory called <em>bulletin</em>. You can
\r
1165 also see that dates they were created. In the case of the file <em>news</em>,
\r
1166 you can also see the time it was last modified, a good clue as to whether the
\r
1167 file has been updated since you last read it. To read the file called
\r
1168 <em>news</em> you would simply issue the command ....
\r
1174 To look what is in the bulletin directory you issue the command ....
\r
1177 show/files bulletin
\r
1178 opdx390 21381 29-Nov-1999 1621Z opdx390.1 1670 29-Nov-1999 1621Z
\r
1179 opdx390.2 2193 29-Nov-1999 1621Z opdx391 25045 29-Nov-1999 1621Z
\r
1180 opdx392 35969 29-Nov-1999 1621Z opdx393 15023 29-Nov-1999 1621Z
\r
1181 opdx394 33429 29-Nov-1999 1621Z opdx394.1 3116 29-Nov-1999 1621Z
\r
1182 opdx395 24319 29-Nov-1999 1621Z opdx396 32647 29-Nov-1999 1621Z
\r
1183 opdx396.1 5537 29-Nov-1999 1621Z opdx396.2 6242 29-Nov-1999 1621Z
\r
1184 opdx397 18433 29-Nov-1999 1621Z opdx398 19961 29-Nov-1999 1621Z
\r
1185 opdx399 17719 29-Nov-1999 1621Z opdx400 19600 29-Nov-1999 1621Z
\r
1186 opdx401 27738 29-Nov-1999 1621Z opdx402 18698 29-Nov-1999 1621Z
\r
1187 opdx403 24994 29-Nov-1999 1621Z opdx404 15685 29-Nov-1999 1621Z
\r
1188 opdx405 13984 29-Nov-1999 1621Z opdx405.1 4166 29-Nov-1999 1621Z
\r
1189 opdx406 28934 29-Nov-1999 1621Z opdx407 24153 29-Nov-1999 1621Z
\r
1190 opdx408 15081 29-Nov-1999 1621Z opdx409 23234 29-Nov-1999 1621Z
\r
1191 Press Enter to continue, A to abort (16 lines) >
\r
1194 You can now read any file in this directory using the type command, like this ....
\r
1197 type bulletin/opdx391
\r
1198 Ohio/Penn DX Bulletin No. 391
\r
1199 The Ohio/Penn Dx PacketCluster
\r
1200 DX Bulletin No. 391
\r
1203 Editor Tedd Mirgliotta, KB8NW
\r
1204 Provided by BARF-80 BBS Cleveland, Ohio
\r
1205 Online at 440-237-8208 28.8k-1200 Baud 8/N/1 (New Area Code!)
\r
1206 Thanks to the Northern Ohio Amateur Radio Society, Northern Ohio DX
\r
1207 Association, Ohio/Penn PacketCluster Network, K1XN & Golist, WB2RAJ/WB2YQH
\r
1208 & The 59(9) DXReport, W3UR & The Daily DX, K3TEJ, KN4UG, W4DC, NC6J, N6HR,
\r
1209 Press Enter to continue, A to abort (508 lines) >
\r
1212 The page length will of course depend on what you have it set to!
\r
1214 <sect1>The Aliases file
\r
1217 You will find a file in /spider/cmd/ called Aliases. This is the file that
\r
1218 controls what a user gets when issuing a command. It is also possible to
\r
1219 create your own aliases for databases and files you create locally.
\r
1222 You should not alter the original file in /spider/cmd/ but create a new file
\r
1223 with the same name in /spider/local_cmd. This means that any new Aliases files
\r
1224 that is downloaded will not overwrite your self created Aliases and also that
\r
1225 you do not override any new Aliases with your copy in /spider/local_cmd/. You
\r
1226 must remember that any files you store in /spider/local/ or /spider/local_cmd
\r
1227 override the originals if the same lines are used in both files.
\r
1230 The best way of dealing with all this then is to only put your own locally
\r
1231 created Aliases in the copy in /spider/local_cmd. The example below is
\r
1232 currently in use at GB7MBC.
\r
1237 # Local Aliases File
\r
1244 '^news$', 'type news', 'type',
\r
1247 '^sh\w*/buck$', 'show/qrz', 'show',
\r
1248 '^sh\w*/hftest$', 'dbshow hftest', 'dbshow',
\r
1249 '^sh\w*/qsl$', 'dbshow qsl', 'dbshow',
\r
1250 '^sh\w*/vhf$', 'dbshow vhf', 'dbshow',
\r
1251 '^sh\w*/vhftest$', 'dbshow vhftest', 'dbshow',
\r
1258 Each alphabetical section should be preceded by the initial letter and the section
\r
1259 should be wrapped in square brackets as you can see. The syntax is straightforward.
\r
1260 The first section on each line is the new command that will be allowed once the
\r
1261 alias is included. The second section is the command it is replacing and the last
\r
1262 section is the actual command that is being used.
\r
1265 The eagle-eyed amongst you will have noticed that in the first section, the new
\r
1266 alias command has a '^' at the start and a '$' at the end. Basically these force
\r
1267 a perfect match on the alias. The '^' says match the beginning exactly and the
\r
1268 '$' says match the end exactly. This prevents unwanted and unintentional matches
\r
1269 with similar commands.
\r
1272 I have 3 different types of alias in this file. At the top is an alias for 'news'.
\r
1273 This is a file I have created in the /spider/packclus/ directory where I can inform
\r
1274 users of new developments or points of interest. In it's initial form a user would
\r
1275 have to use the command <em>type news</em>. The alias allows them to simply type
\r
1276 <em>news</em> to get the info. Second is an alias for the <em>show/qrz</em>
\r
1277 command so that those users used to the original <em>show/buck</em> command in
\r
1278 AK1A will not get an error, and the rest of the lines are for locally created
\r
1279 databases so that a user can type <em>show/hftest</em> instead of having to use
\r
1280 the command <em>dbshow hftest</em> which is not as intuitive.
\r
1283 This file is just an example and you should edit it to your own requirements.
\r
1284 Once created, simply issue the command <em>load/alias</em> at the cluster
\r
1285 prompt as the sysop user and the aliases should be available.
\r
1291 In later versions of Spider a simple console program is provided for the sysop.
\r
1292 This has a type ahead buffer with line editing facilities and colour for spots,
\r
1293 announces etc. To use this program, simply use console.pl instead of client.
\r
1296 To edit the colours, copy /spider/perl/Console.pl to /spider/local and edit the
\r
1297 file with your favourite editor.
\r
1299 <sect1>Updating kepler data
\r
1302 Spider has a powerful and flexible show/satellite command. In order for
\r
1303 this to be accurate, the kepler data has to be updated regularly. In
\r
1304 general, this data is available as an email or via cluster mail.
\r
1305 Updating it is simple. First you need to export the mail message as a
\r
1306 file. You do this with the <em>export</em> command from the cluster prompt
\r
1307 as the sysop. For example ...
\r
1310 export 5467 /spider/perl/keps.in
\r
1314 would export message number 5467 as a file called keps.in in the
\r
1315 /spider/perl directory.
\r
1318 Now login to a VT as sysop and cd /spider/perl. There is a command in
\r
1319 the perl directory called <em>convkeps.pl</em>. All we need to do now is
\r
1320 convert the file like so ...
\r
1323 ./convkeps.pl keps.in
\r
1327 Now go back to the cluster and issue the command ...
\r
1334 That is it! the kepler data has been updated.
\r
1336 <sect1>The QRZ callbook
\r
1339 The command <em>sh/qrz</em> will only work once you have followed a few
\r
1340 simple steps. First you need to get a user ID and password from qrz.com.
\r
1341 Simply go to the site and create one. Secondly you need to copy the file
\r
1342 /spider/perl/Internet.pm to /spider/local and alter it to match your user
\r
1343 ID and password. You also at this point need to set $allow=1 to complete
\r
1344 the setup. Many thanks to Fred Lloyd, the proprieter of
\r
1345 <htmlurl url="http://www.qrz.com" name="qrz.com"> for allowing this access.
\r
1347 <sect1>Connecting logging programs
\r
1350 There appear to be very few logging programs out there that support telnet
\r
1351 especially the popular ones like LogEQF, Turbolog etc. This can make it
\r
1352 difficult to connect to your own cluster!
\r
1353 The way to do it is to make the logging program think it has a TNC attached
\r
1354 to a com port on the logging PC and 'push' a linux login out to it.
\r
1355 This is achieved very simply by the use of <em>agetty</em>.
\r
1358 All that is required is to add a line in /etc/inittab to have the client
\r
1359 ready for a connection on the com port of your choice. Remember that in
\r
1360 Linux, the com ports start at ttyS0 for com1, ttyS1 for com2 etc.
\r
1363 c4:2345:respawn:/sbin/agetty -L 9600 ttyS1
\r
1367 Add this after the standard runlevel lines in /etc/inittab. The above
\r
1368 line works on ttyS1 (com2). Now as root, issue the command <em>telinit q</em>
\r
1369 and it should be ready for connection. All that is required is a 3 wire
\r
1370 serial lead (tx, rx and signal ground). Tell you logging program to use
\r
1371 8n1 at 9600 baud and you should see a Linux login prompt. Login as normal
\r
1372 and then telnet from there to the cluster.
\r
1374 <sect>Java Web applet
\r
1377 In the spider tree will be a directory <em>spider-web</em>. This is a
\r
1378 neat little java web applet that can be run from a website. The applet
\r
1379 must run on the same machine as the cluster. The included README file is
\r
1383 I should comment here that the applet is precompiled, that is, ready to go.
\r
1384 It was compiled using JDK1.3.1. If your version is earlier than this then it
\r
1385 may not work. Should that be the case you need to recompile or update your
\r
1386 JDK. To recompile do the following ...
\r
1389 cd /spider/spider-web
\r
1391 /usr/bin/javac spiderclient.java
\r
1395 I have used /usr/bin/javac as an example, your path to javac may be different.
\r
1400 Completely based on a clx web client written in Java by dl6dbh
\r
1401 (ftp://clx.muc.de/pub/clx/clx-java_10130001.tgz)
\r
1403 The webserver has to run on the same machine as your DxSpider software!
\r
1405 It is assumed that you have Java installed. You need JDK1.3.1 at least.
\r
1407 Installation instructions (Performed as root):
\r
1409 Put all the files in the spider-web directory into a newly created directory
\r
1410 under the DocumentRoot of your websever for instance 'client'. In my case
\r
1411 this is: /home/httpd/html/client/ although ymmv. For Suse the correct
\r
1412 path should be /usr/local/httpd/htdocs/client/ for example.
\r
1414 Move spider.cgi to the cgi-bin directory of your webserver, in my case that is
\r
1415 /home/httpd/cgi-bin/ although ymmv. For Suse the correct path should be
\r
1416 /usr/local/httpd/cgi-bin/ for example.
\r
1418 Change the permissions of the files to ensure they are correct, obviously you
\r
1419 will need to use the correct path the the files according to your system:
\r
1421 chmod 755 /home/httpd/html/cgi-bin/spider.cgi
\r
1422 chmod -R 755 /home/httpd/html/client/
\r
1424 By default the spider.cgi script should pick up your hostname (As long as this
\r
1425 is set correctly). If it does not or your hostname differs from the name that
\r
1426 you attach to the public address that you are using, then edit spider.cgi :
\r
1428 # Uncomment and set the hostname manually here if the above fails.
\r
1429 # $HOSTNAME = "gb7mbc.spoo.org" ;
\r
1432 'HOSTNAME' is the hostname of your cluster.
\r
1434 'PORT' is the portnumber that you use to connect to your DxSpider via
\r
1435 telnet (see Listeners.pm)
\r
1437 NOTE: If you can start the console but cannot connect to the cluster from it,
\r
1438 then it is possible that the machine you are on cannot resolve the hostname of
\r
1439 your cluster machine. If this is the case, you need to set your hostname
\r
1440 manually as above.
\r
1442 You also need to set the $NODECALL variable. This prints the name of your
\r
1443 choosing (probably your cluster callsign) on the html page.
\r
1445 You now can connect to Spider-Web via http://yourserver/cgi-bin/spider.cgi
\r
1448 <sect>Web based statistics
\r
1451 From version 1.50, you can use the freeware software MRTG to produce
\r
1452 really nice graphical statistics on your web site. For an example
\r
1453 try <htmlurl url="http://www.gb7mbc.net/mrtg/stats.html" name="http://www.gb7mbc.net/mrtg/stats.html">.
\r
1456 The following should help you get it all working.
\r
1459 First you need to download the latest version of MRTG from <htmlurl url="http://people.ee.ethz.ch/~oetiker/webtools/mrtg/" name="http://people.ee.ethz.ch/~oetiker/webtools/mrtg/">.
\r
1460 You will also need the following files..
\r
1463 libpng-1.0.14.tar.gz
\r
1468 Login to your machine as the root user, put all the downloaded files
\r
1469 in /usr/local/src/ (or wherever you prefer) and untar and compile them.
\r
1470 All the information to compile and install these sources come with them.
\r
1471 After compilation and installation, you will find MRTG in /usr/local/mrtg-2.
\r
1474 Now copy all the files in /usr/local/src/mrtg-2.9.22/images/ to
\r
1475 /spider/html/mrtg/
\r
1478 You now need to make 2 symbolic links like below...
\r
1481 ln -s /usr/local/mrtg-2/bin/mrtg /usr/bin/mrtg
\r
1482 ln -s /usr/local/mrtg-2/lib/mrtg2 /usr/lib/mrtg2
\r
1486 Now login to the cluster with your sysop callsign and run the command
\r
1489 <P>Now you are nearly there! Login as the sysop user and change to the
\r
1490 /spider/html/mrtg/ directory. Now run the command <em>indexmaker</em> as
\r
1494 indexmaker --output stats.html --columns=1 --title "MRTG statistics for GB7DJK" ../../mrtg/mrtg.cfg
\r
1497 Changing the callsign for your own cluster callsign of course!
\r
1500 And finally you need to login as the root user and create one last
\r
1501 symbolic link. Where this points will depend on where your html
\r
1502 documents are kept. For RedHat systems you use...
\r
1505 ln -s /home/sysop/spider/html/mrtg /home/httpd/html/mrtg
\r
1508 and for SuSE systems...
\r
1511 ln -s /home/sysop/spider/html/mrtg /usr/local/httpd/htdocs/mrtg
\r
1514 If you now point your browser to your website as below it should all
\r
1518 http://www.xxx.xxx/mrtg/stats.html
\r
1521 Of course, to get the stats to update, you need to add some information
\r
1522 in the spider crontab file as below...
\r
1525 # Update stats for mrtg on website
\r
1526 00,05,10,15,20,25,30,35,40,45,50,55 * * * * run_cmd('mrtg all')
\r
1529 This will update the site every 5 minutes.
\r
1534 From version 1.49 DXSpider has some additional security features. These
\r
1535 are not by any means meant to be exhaustive, however they do afford some
\r
1536 security against piracy. These two new features can be used independently
\r
1537 of each other or in concert to tighten the security.
\r
1539 <sect1>Registration
\r
1542 The basic principle of registration is simple. If a user is not registered
\r
1543 by the sysop, then they have read-only access to the cluster. The only
\r
1544 thing they can actually send is a talk or a message to the sysop. In
\r
1545 order for them to be able to spot, send announces or talks etc the sysop
\r
1546 must register them with the <em>set/register</em> command, like this ...
\r
1549 set/register g0vgs
\r
1552 The user g0vgs can now fully use the cluster. In order to enable
\r
1553 registration, you can issue the command ...
\r
1556 set/var $main::reqreg = 1
\r
1559 Any users that are not registered will now see the motd_nor file rather
\r
1560 than the motd file as discussed in the Information, files and useful
\r
1564 Entering this line at the prompt will only last for the time the cluster
\r
1565 is running of course and would not be present on a restart. To make the
\r
1566 change permanent, add the above line to /spider/scripts/startup. To
\r
1567 read more on the startup file, see the section on Information, files
\r
1568 and useful programs.
\r
1571 To unregister a user use <em>unset/register</em> and to show the list
\r
1572 of registered users, use the command <em>show/register</em>.
\r
1577 At the moment, passwords only affect users who login to a DXSpider
\r
1578 cluster node via telnet. If a user requires a password, they can
\r
1579 either set it themselves or have the sysop enter it for them by using
\r
1580 the <em>set/password</em> command. Any users who already have passwords,
\r
1581 such as remote sysops, will be asked for their passwords automatically
\r
1582 by the cluster. Using passwords in this way means that the user has a
\r
1583 choice on whether to have a password or not. To force the use of
\r
1584 passwords at login, issue the command ...
\r
1587 set/var $main::passwdreq = 1
\r
1590 at the cluster prompt. This can also be added to the /spider/scripts/startup
\r
1591 file as above to make the change permanent.
\r
1594 Of course, if you do this you will have to assign a password for each of
\r
1595 your users. If you were asking them to register, it is anticipated that
\r
1596 you would ask them to send you a message both to ask to be registered and
\r
1597 to give you the password they wish to use.
\r
1600 Should a user forget their password, it can be reset by the sysop by
\r
1601 first removing the existing password and then setting a new one like so ...
\r
1604 unset/password g0vgs
\r
1605 set/password g0vgs new_password
\r
1610 <sect1>CVS from a Linux platform
\r
1613 CVS stands for "Concurrent Versions System" and the CVS for DXSpider is held
\r
1614 at <htmlurl url="http://www.sourceforge.net" name="Sourceforge">. This means
\r
1615 that it is possible to update your DXSpider installation to the latest
\r
1616 sources by using a few simple commands. A graphical interface to CVS for
\r
1617 Windows is explained in the next section.
\r
1620 Please be aware that if you update your system using CVS, it is possible that
\r
1621 you could be running code that is very beta and not fully tested. There is
\r
1622 a possibility that it could be unstable.
\r
1625 I am of course assuming that you have a machine with both DXSpider and
\r
1626 Internet access running.
\r
1629 BEFORE YOU EVEN CONSIDER STARTING WITH THIS MAKE A BACKUP OF YOUR
\r
1630 ENTIRE SPIDER TREE!!
\r
1633 Assuming you are connected to the Internet, you need to login to the
\r
1634 CVS repository and then update your Spider source. There are several
\r
1635 steps which are listed below ...
\r
1638 First login as the user <em>sysop</em>. Next you need to connect to the CVS
\r
1639 repository. You do this with the command below ...
\r
1642 cvs -d:pserver:anonymous@cvs.DXSpider.sourceforge.net:/cvsroot/dxspider login
\r
1645 You will get a password prompt. Simply hit return here and your machine should
\r
1646 return to a normal linux prompt.
\r
1649 What happens next depends on whether you have an existing installation that
\r
1650 you want to update with the latest and greatest or whether you just want
\r
1651 to see what is there and/or run it on a new machine for testing.
\r
1653 If you are installing Spider from CVS then change directory to /home/sysop
\r
1655 If you are wanting to update Spider then cd to /tmp
\r
1658 The next step will create a brand new 'spider' directory in your current
\r
1662 cvs -z3 -d:pserver:anonymous@cvs.DXSpider.sourceforge.net:/cvsroot/dxspider co spider
\r
1665 This command is all on one line.
\r
1668 Hopefully your screen should show you downloading files. The -z3 simply compresses
\r
1669 the download to improve speed.
\r
1670 When this has finished, you will have exactly the same as if you had untarred a full
\r
1671 tarball PLUS some extra directories and files that CVS needs to do the magic that
\r
1675 Now if you are doing a new installation, that's it. Carry on as if you have
\r
1676 just downloaded and untarred the lastest tarball.
\r
1679 If you want to upgrade your current installation then do this ...
\r
1682 tar cvfz /tmp/s.tgz spider
\r
1684 tar xvfzp /tmp/s.tgz
\r
1687 This is assuming you downloaded to the /tmp directory of course.
\r
1690 NOTE: the 'p' on the end of the 'xvfz' is IMPORTANT! It keeps the permissions
\r
1691 correct. YOU WERE LOGGED IN AS THE USER SYSOP WEREN'T YOU?????
\r
1693 Remember to recompile the C client (cd /spider/src; make)
\r
1696 At this point the files have been upgraded. You can (usually) restart the cluster
\r
1697 in your own time. However, if you attempt to use any new commands or features
\r
1698 expect it to be fatal! At least your cluster will have been restarted then so it
\r
1699 will be too late to worry about it!
\r
1702 Now the magic part! From now on when you want to update, simply connect to the
\r
1703 Internet and then, as the user <em>sysop</em> ...
\r
1710 and your files will be updated. As above, remember to recompile the "C" client
\r
1711 if it has been updated (CVS will tell you) and restart if any of the perl scripts
\r
1712 have been altered or added, again, CVS will tell you.
\r
1715 You will find any changes documented in the /spider/Changes file.
\r
1717 <sect1>CVS from a Windows platform
\r
1720 After the initial setup, an update to your DXSpider software is no more than a couple
\r
1721 of clicks away. This section is intended to explain and illustrate the use of the
\r
1722 WinCVS application to update your DXSpider software. The current stable version of
\r
1723 WinCVS is Ver. 1.2. You can get this software at:
\r
1725 <htmlurl url="http://prdownloads.sourceforge.net/cvsgui/WinCvs120.zip" name="http://prdownloads.sourceforge.net/cvsgui/WinCvs120.zip">
\r
1727 Pick your download mirror and then install WinCVS after the download is complete.
\r
1729 In this next section I have included a series of links to .jpg files to take advantage of the
\r
1730 picture and 1000 words equivalency. The .jpg files are in the C:\spider\html directory. If
\r
1731 someone using a Linux system is reading this section from boredom, the files are in
\r
1732 /home/sysop/spider/html. One aside, a Linux user can also get a copy of gcvs and do your updates
\r
1733 graphically as opposed to from the command line. The following descriptions are almost identical
\r
1734 between WinCvs and gcvs. The following screen shots have duplicate links, depending upon whether
\r
1735 you are viewing this information under the Windows or Linux operating system.
\r
1737 When WinCVS is installed, running, and you are connected to the internet, the initial screen looks like:
\r
1739 <htmlurl url="initial.jpg" name="initial.jpg">
\r
1741 If you want, you can also look at these .jpg files with another viewer that might provide some
\r
1742 better clarity to the image. On the left is the directory tree for your hard disk. Notice that
\r
1743 the spider directory has a gray highlight.
\r
1745 To start configuring WinCVS, click on Admin at the top of the screen and then Preferences. This
\r
1748 <htmlurl url="pref-gen.jpg" name="pref-gen.jpg">
\r
1750 In the top line for CVSROOT, enter:
\r
1752 anonymous@cvs.DXSpider.sourceforge.net:/cvsroot/dxspider login
\r
1757 "passwd" file on the cvs server
\r
1760 for Authentication on the General tab.
\r
1762 Next, move to the right to the Ports tab.
\r
1764 <htmlurl url="pref-ports.jpg" name="pref-ports.jpg">
\r
1766 In here, check the box on the second line down for the "pserver" port. Enter a port number of 2401.
\r
1768 Finally, go to the WinCvs tab all the way to the right.
\r
1770 <htmlurl url="pref-wincvs.jpg" name="pref-wincvs.jpg">
\r
1772 Enter Notepad as the viewer to open files. For the HOME folder, put "C:\spider" and click OK
\r
1773 because the configuration is now complete.
\r
1775 You are now ready to upgrade your copy of DXSpider. Click on the greyed Spider folder
\r
1776 shown in the directory tree on the left of the WinCVS display. Two things should happen. The Spider
\r
1777 folder will be selected and the greyed-out arrow located just below the word Query in the top line will
\r
1778 turn to solid green.
\r
1780 For anyone using gcvs under Linux, the green arrow is located on the extreme left of the display,
\r
1781 under the word File. A gcvs screen looks like:
\r
1783 <htmlurl url="gcvs.jpg" name="gcvs.jpg">
\r
1785 Click on the now green arrow to start the download process. An Update Settings box will be displayed
\r
1786 to which you can simply say OK.
\r
1788 <htmlurl url="update-OK.jpg" name="update-OK.jpg">
\r
1790 For future reference, the Update Settings box is the place where you can enter information to revert
\r
1791 to a prior version of DXSpider. Information on reverting to a Before Date is contained in the WinCVS
\r
1794 After a short period of time, a series of file names will scroll by in the lower pane of the WinCVS
\r
1795 window. Eventually you should see
\r
1797 *****CVS exited normally with code 0*****
\r
1800 appear in the lower pane. You're done. The updated files are in place ready for you to stop and then
\r
1801 restart your DXSpider. After the restart, you're running with the latest version of DXSpider.
\r
1803 <htmlurl url="completed.jpg" name="completed.jpg">
\r
1805 To paraphrase from the CVS section... Now the magic part! From now on when you want to update, simply
\r
1806 connect to the Internet and start WinCVS.
\r
1808 Click on the greyed-out Spider directory in the left screen
\r
1809 Click on the green down arrow
\r
1810 Click OK on the Update Settings dialog box
\r
1811 Restart your Spider software
\r
1814 <sect>The DXSpider command set
\r
1821 <bf>accept</bf> Set a filter to accept something
1825 Create a filter to accept something
1827 There are 2 types of filter, accept and reject. See HELP FILTERING for more
1829 <sect1>accept/announce <call> [input] [0-9] <pattern> (8)
1833 <bf>accept/announce <call> [input] [0-9] <pattern></bf> Announce filter sysop version
1837 This version allows a sysop to set a filter for a callsign as well as the
1838 default for nodes and users eg:-
1842 accept/ann input node_default by G,M,2
1843 accept/ann user_default by G,M,2
1846 <sect1>accept/announce [0-9] <pattern> (0)
1850 <bf>accept/announce [0-9] <pattern></bf> Set an 'accept' filter line for announce
1854 Create an 'accept this announce' line for a filter.
1856 An accept filter line means that if the announce matches this filter it is
1857 passed onto the user. See HELP FILTERING for more info. Please read this
1858 to understand how filters work - it will save a lot of grief later on.
1860 You can use any of the following things in this line:-
1863 info <string> eg: iota or qsl
1864 by <prefixes> eg: G,M,2
1865 origin <prefixes>
1866 origin_dxcc <prefixes or numbers> eg: 61,62 (from eg: sh/pre G)
1867 origin_itu <prefixes or numbers> or: G,GM,GW
1868 origin_zone <prefixes or numbers>
1869 origin_state <states> eg: VA,NH,RI,NH
1870 by_dxcc <prefixes or numbers>
1871 by_itu <prefixes or numbers>
1872 by_zone <prefixes or numbers>
1873 by_state <states>
1874 channel <prefixes>
1875 wx 1 filter WX announces
1876 dest <prefixes> eg: 6MUK,WDX (distros)
1883 acc/ann 2 by_zone 14,15,16
1884 (this could be all on one line: acc/ann dest 6MUK or by_zone 14,15,16)
1894 acc/ann by_state va,nh,ri,nh
1897 You can use the tag 'all' to accept everything eg:
1903 but this probably for advanced users...
1904 <sect1>accept/route <call> [0-9] <pattern> (8)
1908 <bf>accept/route <call> [0-9] <pattern></bf> Set an 'accept' filter line for routing
1912 Create an 'accept this routing PC Protocol' line for a filter.
1914 An accept filter line means that if a PC16/17/19/21/24/41/50 matches this filter
1915 it is passed thru that interface. See HELP FILTERING for more info. Please read this
1916 to understand how filters work - it will save a lot of grief later on.
1918 You can use any of the following things in this line:-
1921 call <prefixes> the callsign of the thingy
1922 call_dxcc <prefixes or numbers> eg: 61,62 (from eg: sh/pre G)
1923 call_itu <prefixes or numbers> or: G,GM,GW
1924 call_zone <prefixes or numbers>
1925 call_state <states> eg: VA,NH,RI,NH
1926 origin <prefixes> really the interface it came in on
1927 origin_dxcc <prefixes or numbers> eg: 61,62 (from eg: sh/pre G)
1928 origin_itu <prefixes or numbers> or: G,GM,GW
1929 origin_zone <prefixes or numbers>
1930 origin_state <states> eg: VA,NH,RI,NH
1936 acc/route gb7djk call_dxcc 61,38 (send only UK+EIRE nodes)
1937 acc/route gb7djk call gb7djk (equiv to SET/ISOLATE)
1940 you can now use 'by' as a synonym for 'call' so:
1949 You can use the tag 'all' to accept everything eg:
1955 <sect1>accept/spots <call> [input] [0-9] <pattern> (8)
1959 <bf>accept/spots <call> [input] [0-9] <pattern></bf> Spot filter sysop version
1963 This version allows a sysop to set a filter for a callsign as well as the
1964 default for nodes and users eg:-
1967 accept/spot db0sue-7 1 by_zone 14,15,16
1968 accept/spot node_default all
1969 set/hops node_default 10
1973 accept/spot user_default by G,M,2
1976 <sect1>accept/spots [0-9] <pattern> (0)
1980 <bf>accept/spots [0-9] <pattern></bf> Set an 'accept' filter line for spots
1984 Create an 'accept this spot' line for a filter.
1986 An accept filter line means that if the spot matches this filter it is
1987 passed onto the user. See HELP FILTERING for more info. Please read this
1988 to understand how filters work - it will save a lot of grief later on.
1990 You can use any of the following things in this line:-
1993 freq <range> eg: 0/30000 or hf or hf/cw or 6m,4m,2m
1994 on <range> same as 'freq'
1995 call <prefixes> eg: G,PA,HB9
1996 info <string> eg: iota or qsl
1998 call_dxcc <prefixes or numbers> eg: 61,62 (from eg: sh/pre G)
1999 call_itu <prefixes or numbers> or: G,GM,GW
2000 call_zone <prefixes or numbers>
2001 call_state <states> eg: VA,NH,RI,ME
2002 by_dxcc <prefixes or numbers>
2003 by_itu <prefixes or numbers>
2004 by_zone <prefixes or numbers>
2005 by_state <states> eg: VA,NH,RI,ME
2006 origin <prefixes>
2007 channel <prefixes>
2010 'call' means the callsign that has spotted 'by' whoever.
2012 For frequencies, you can use any of the band names defined in
2013 SHOW/BANDS and you can use a subband name like: cw, rtty, data, ssb -
2014 thus: hf/ssb. You can also just have a simple range like: 0/30000 -
2015 this is more efficient than saying simply: freq HF (but don't get
2016 too hung up about that)
2022 acc/spot 2 on vhf and (by_zone 14,15,16 or call_zone 14,15,16)
2025 You can use the tag 'all' to accept everything, eg:
2034 acc/spots by_state VA,NH,RI,MA,ME
2037 but this probably for advanced users...
2038 <sect1>accept/wcy <call> [input] [0-9] <pattern> (8)
2042 <bf>accept/wcy <call> [input] [0-9] <pattern></bf> WCY filter sysop version
2046 This version allows a sysop to set a filter for a callsign as well as the
2047 default for nodes and users eg:-
2050 accept/wcy node_default all
2051 set/hops node_default 10
2054 <sect1>accept/wcy [0-9] <pattern> (0)
2058 <bf>accept/wcy [0-9] <pattern></bf> set an 'accept' WCY filter
2062 It is unlikely that you will want to do this, but if you do then you can
2063 filter on the following fields:-
2066 by <prefixes> eg: G,M,2
2067 origin <prefixes>
2068 origin_dxcc <prefixes or numbers> eg: 61,62 (from eg: sh/pre G)
2069 origin_itu <prefixes or numbers> or: G,GM,GW
2070 origin_zone <prefixes or numbers>
2071 by_dxcc <prefixes or numbers>
2072 by_itu <prefixes or numbers>
2073 by_zone <prefixes or numbers>
2074 channel <prefixes>
2077 There are no examples because WCY Broadcasts only come from one place and
2078 you either want them or not (see UNSET/WCY if you don't want them).
2080 This command is really provided for future use.
2082 See HELP FILTER for information.
2083 <sect1>accept/wwv <call> [input] [0-9] <pattern> (8)
2087 <bf>accept/wwv <call> [input] [0-9] <pattern></bf> WWV filter sysop version
2091 This version allows a sysop to set a filter for a callsign as well as the
2092 default for nodes and users eg:-
2095 accept/wwv db0sue-7 1 by_zone 4
2096 accept/wwv node_default all
2097 set/hops node_default 10
2101 accept/wwv user_default by W,K
2104 <sect1>accept/wwv [0-9] <pattern> (0)
2108 <bf>accept/wwv [0-9] <pattern></bf> set an 'accept' WWV filter
2112 It is unlikely that you will want to do this, but if you do then you can
2113 filter on the following fields:-
2116 by <prefixes> eg: G,M,2
2117 origin <prefixes>
2118 origin_dxcc <prefixes or numbers> eg: 61,62 (from eg: sh/pre G)
2119 origin_itu <prefixes or numbers> or: G,GM,GW
2120 origin_zone <prefixes or numbers>
2121 by_dxcc <prefixes or numbers>
2122 by_itu <prefixes or numbers>
2123 by_zone <prefixes or numbers>
2124 channel <prefixes>
2130 accept/wwv by_zone 4
2133 is probably the only useful thing to do (which will only show WWV broadcasts
2134 by stations in the US).
2136 See HELP FILTER for information.
2137 <sect1>announce <text> (0)
2141 <bf>announce <text></bf> Send an announcement to LOCAL users only
2145 <text> is the text of the announcement you wish to broadcast
2146 <sect1>announce full <text> (0)
2150 <bf>announce full <text></bf> Send an announcement cluster wide
2154 This will send your announcement cluster wide
2155 <sect1>announce sysop <text> (5)
2159 <bf>announce sysop <text></bf> Send an announcement to Sysops only
2163 <sect1>apropos <string> (0)
2167 <bf>apropos <string></bf> Search help database for <string>
2171 Search the help database for <string> (it isn't case sensitive), and print
2172 the names of all the commands that may be relevant.
2173 <sect1>blank [<string>] [<nn>] (0)
2177 <bf>blank [<string>] [<nn>]</bf> Print nn (default 1) blank lines (or strings)
2181 In its basic form this command prints one or more blank lines. However if
2182 you pass it a string it will replicate the string for the width of the
2183 screen (default 80) and then print that one or more times, so:
2189 prints two blank lines
2195 prints a row of - characters once.
2201 prints 'abcabcabcabcabcabc....'
2203 This is really only of any use in a script file and you can print a maximum
2209 <bf>bye</bf> Exit from the cluster
2213 This will disconnect you from the cluster
2214 <sect1>catchup <node call> all|[<msgno> ...] (5)
2218 <bf>catchup <node call> all|[<msgno> ...]</bf> Mark a message as sent
2222 <sect1>clear/announce <callsign> [input] [0-9|all] (8)
2226 <bf>clear/announce <callsign> [input] [0-9|all]</bf> Clear a announce filter line
2230 A sysop can clear an input or normal output filter for a user or the
2231 node_default or user_default.
2232 <sect1>clear/announce [1|all] (0)
2236 <bf>clear/announce [1|all]</bf> Clear a announce filter line
2240 This command allows you to clear (remove) a line in a annouce filter or to
2241 remove the whole filter.
2243 see CLEAR/SPOTS for a more detailed explanation.
2244 <sect1>clear/route <callsign> [input] [0-9|all] (8)
2248 <bf>clear/route <callsign> [input] [0-9|all]</bf> Clear a route filter line
2252 A sysop can clear an input or normal output filter for a user or the
2253 node_default or user_default.
2254 <sect1>clear/route [1|all] (0)
2258 <bf>clear/route [1|all]</bf> Clear a route filter line
2262 This command allows you to clear (remove) a line in a route filter or to
2263 remove the whole filter.
2265 see CLEAR/SPOTS for a more detailed explanation.
2266 <sect1>clear/spots <callsign> [input] [0-9|all] (8)
2270 <bf>clear/spots <callsign> [input] [0-9|all]</bf> Clear a spot filter line
2274 A sysop can clear an input or normal output filter for a user or the
2275 node_default or user_default.
2276 <sect1>clear/spots [0-9|all] (0)
2280 <bf>clear/spots [0-9|all]</bf> Clear a spot filter line
2284 This command allows you to clear (remove) a line in a spot filter or to
2285 remove the whole filter.
2287 If you have a filter:-
2291 acc/spot 2 on vhf and (by_zone 14,15,16 or call_zone 14,15,16)
2300 you will be left with:-
2303 acc/spot 2 on vhf and (by_zone 14,15,16 or call_zone 14,15,16)
2312 the filter will be completely removed.
2313 <sect1>clear/wcy <callsign> [input] [0-9|all] (8)
2317 <bf>clear/wcy <callsign> [input] [0-9|all]</bf> Clear a WCY filter line
2321 A sysop can clear an input or normal output filter for a user or the
2322 node_default or user_default.
2323 <sect1>clear/wcy [1|all] (0)
2327 <bf>clear/wcy [1|all]</bf> Clear a WCY filter line
2331 This command allows you to clear (remove) a line in a WCY filter or to
2332 remove the whole filter.
2334 see CLEAR/SPOTS for a more detailed explanation.
2335 <sect1>clear/wwv <callsign> [input] [0-9|all] (8)
2339 <bf>clear/wwv <callsign> [input] [0-9|all]</bf> Clear a WWV filter line
2343 A sysop can clear an input or normal output filter for a user or the
2344 node_default or user_default.
2345 <sect1>clear/wwv [1|all] (0)
2349 <bf>clear/wwv [1|all]</bf> Clear a WWV filter line
2353 This command allows you to clear (remove) a line in a WWV filter or to
2354 remove the whole filter.
2356 see CLEAR/SPOTS for a more detailed explanation.
2357 <sect1>connect <callsign> (5)
2361 <bf>connect <callsign></bf> Start a connection to another DX Cluster
2365 Start a connection process that will culminate in a new connection to the
2366 DX cluster <callsign>. This process creates a new 'client' process which will
2367 use the script in /spider/connect/<callsign> to effect the 'chat' exchange
2368 necessary to traverse the network(s) to logon to the cluster <callsign>.
2373 <bf>dbavail</bf> Show a list of all the Databases in the system
2377 Title says it all really, this command lists all the databases defined
2378 in the system. It is also aliased to SHOW/COMMAND.
2379 <sect1>dbcreate <name> (9)
2383 <bf>dbcreate <name></bf> Create a database entry
2387 <sect1>dbcreate <name> chain <name> [<name>..] (9)
2391 <bf>dbcreate <name> chain <name> [<name>..]</bf> Create a chained database entry
2395 <sect1>dbcreate <name> cmd <dxspider command> (9)
2399 <bf>dbcreate <name> cmd <dxspider command></bf> make a local command available as a DB
2403 DBCREATE allows you to define a database in the system. It doesn't actually
2404 create anything, just defines it.
2406 The databases that are created are simple DB_File hash databases, they are
2407 therefore already 'indexed'.
2409 You can define a local database with the first form of the command eg:
2415 You can also chain databases with the addition of the 'chain' keyword.
2416 This will search each database one after the other. A typical example
2420 DBCREATE sdx_qsl chain sql_ad
2423 No checking is done to see if the any of the chained databases exist, in
2424 fact it is usually better to do the above staement first then do each of
2425 the chained databases.
2427 Databases can exist offsite. To define a database that lives on another
2431 DBCREATE buckmaster remote gb7dxc
2434 Remote databases cannot be chained; however, the last database in a
2435 a chain can be a remote database eg:
2438 DBCREATE qsl chain gb7dxc
2441 To see what databases have been defined do:
2444 DBAVAIL (or it will have been aliased to SHOW/COMMAND)
2447 It would be normal for you to add an entry into your local Aliases file
2448 to allow people to use the 'SHOW/<dbname>' style syntax. So you would
2449 need to add a line like:-
2455 '^sh\w*/buc', 'dbshow buckmaster', 'dbshow',
2467 to work as they may be used to.
2469 You can also make local commands available as 'pseudo' databases. You
2470 can therefore make spider special commands available as a database. I
2471 imagine that this will be primarily useful for remote access from
2472 legacy nodes. For example:-
2475 DBCREATE dxqsl cmd show/dxqsl
2478 You also use one of these databases in a chain. This may be useful
2481 See DBIMPORT for the importing of existing AK1A format data to databases.
2482 See DBSHOW for generic database enquiry
2484 <sect1>dbcreate <name> remote <node> (9)
2488 <bf>dbcreate <name> remote <node></bf> Create a remote database entry
2492 <sect1>dbimport <dbname> <filename> (9)
2496 <bf>dbimport <dbname> <filename></bf> Import AK1A data into a database
2500 If you want to import or update data in bulk to a database you can use
2501 this command. It will either create or update entries into an existing
2502 database. For example:-
2505 DBIMPORT oblast /tmp/OBLAST.FUL
2508 will import the standard OBLAST database that comes with AK1A into the
2509 oblast database held locally.
2510 <sect1>dbremove <dbname> (9)
2514 <bf>dbremove <dbname></bf> Delete a database
2518 DBREMOVE will completely remove a database entry and also delete any data
2519 file that is associated with it.
2521 There is no warning, no comeback, no safety net.
2529 will remove the oblast database from the system and it will also remove
2530 the associated datafile.
2534 There is no warning, no comeback, no safety net.
2536 You have been warned.
2537 <sect1>dbshow <dbname> <key> (0)
2541 <bf>dbshow <dbname> <key></bf> Display an entry, if it exists, in a database
2545 This is the generic user interface to the database to the database system.
2546 It is expected that the sysop will add an entry to the local Aliases file
2547 so that users can use the more familiar AK1A style of enquiry such as:
2553 but if he hasn't and the database really does exist (use DBAVAIL or
2554 SHOW/COMMAND to find out) you can do the same thing with:
2564 <bf>debug</bf> Set the cluster program into debug mode
2568 Executing this command will only have an effect if you are running the cluster
2575 It will interrupt the cluster just after the debug command has finished.
2576 <sect1>delete/usdb <callsign> ... (9)
2580 <bf>delete/usdb <callsign> ...</bf> Delete this user from the US State Database
2584 This command will completely remove a one or more callsigns
2585 from the US States database.
2587 There is NO SECOND CHANCE.
2589 It goes without saying that you should use this command CAREFULLY!
2591 Note that these callsign may be re-instated by any weekly updates from
2593 <sect1>delete/user <callsign> ... (9)
2597 <bf>delete/user <callsign> ...</bf> Delete this user from the User Database
2601 This command will completely remove a one or more users from the database.
2603 There is NO SECOND CHANCE.
2605 It goes without saying that you should use this command CAREFULLY!
2606 <sect1>demonstrate <call> <command> (9)
2610 <bf>demonstrate <call> <command></bf> Demonstrate a command to another user
2614 This command is provided so that sysops can demonstrate commands to
2615 other users. It runs a command as though that user had typed it in and
2616 then sends the output to that user, together with the command that
2620 DEMO g7brn sh/dx iota oc209
2624 Note that this command is similar to SPOOF and will have the same side
2625 effects. Commands are run at the privilege of the user which is being
2627 <sect1>directory (0)
2631 <bf>directory</bf> List messages
2635 <sect1>directory <from>-<to> (0)
2639 <bf>directory <from>-<to></bf> List messages <from> message <to> message
2643 List the messages in the messages directory.
2645 If there is a 'p' one space after the message number then it is a
2646 personal message. If there is a '-' between the message number and the
2647 'p' then this indicates that the message has been read.
2649 You can use shell escape characters such as '*' and '?' in the <call>
2652 You can combine some of the various directory commands together eg:-
2659 DIR SUBJECT IOTA 200-250
2662 You can abbreviate all the commands to one letter and use ak1a syntax:-
2669 <sect1>directory <nn> (0)
2673 <bf>directory <nn></bf> List last <nn> messages
2677 <sect1>directory all (0)
2681 <bf>directory all</bf> List all messages
2685 <sect1>directory from <call> (0)
2689 <bf>directory from <call></bf> List all messages from <call>
2693 <sect1>directory new (0)
2697 <bf>directory new</bf> List all new messages
2701 <sect1>directory own (0)
2705 <bf>directory own</bf> List your own messages
2709 <sect1>directory subject <string> (0)
2713 <bf>directory subject <string></bf> List all messages with <string> in subject
2717 <sect1>directory to <call> (0)
2721 <bf>directory to <call></bf> List all messages to <call>
2725 <sect1>directory- (5)
2733 Sysops can see all users' messages.
2734 <sect1>disconnect <call> [<call> ...] (8)
2738 <bf>disconnect <call> [<call> ...]</bf> Disconnect a user or cluster
2742 Disconnect any <call> connected locally
2743 <sect1>dx [by <call>] <freq> <call> <remarks> (0)
2747 <bf>dx [by <call>] <freq> <call> <remarks></bf> Send a DX spot
2751 This is how you send a DX Spot to other users. You can, in fact, now
2752 enter the <freq> and the <call> either way round.
2760 will all give the same result. You can add some remarks to the end
2761 of the command and they will be added to the spot.
2764 DX FR0G 144600 this is a test
2767 You can credit someone else by saying:-
2770 DX by G1TLH FR0G 144.600 he isn't on the cluster
2773 The <freq> is compared against the available bands set up in the
2774 cluster. See SHOW/BANDS for more information.
2775 <sect1>echo <line> (0)
2779 <bf>echo <line></bf> Echo the line to the output
2783 This command is useful in scripts and so forth for printing the
2784 line that you give to the command to the output. You can use this
2785 in user_default scripts and the SAVE command for titling and so forth
2787 The script will interpret certain standard "escape" sequences as follows:-
2790 \t - becomes a TAB character (0x09 in ascii)
2791 \a - becomes a BEEP character (0x07 in ascii)
2792 \n - prints a new line
2795 So the following example:-
2798 echo GB7DJK is a dxcluster
2804 GB7DJK is a dxcluster
2807 on the output. You don't need a \n on the end of the line you want to send.
2809 A more complex example:-
2812 echo GB7DJK\n\tg1tlh\tDirk\n\tg3xvf\tRichard
2825 <sect1>export <msgno> <filename> (9)
2829 <bf>export <msgno> <filename></bf> Export a message to a file
2833 Export a message to a file. This command can only be executed on a local
2834 console with a fully privileged user. The file produced will be in a form
2835 ready to be imported back into the cluster by placing it in the import
2836 directory (/spider/msg/import).
2838 This command cannot overwrite an existing file. This is to provide some
2839 measure of security. Any files written will owned by the same user as the
2840 main cluster, otherwise you can put the new files anywhere the cluster can
2841 access. For example:-
2847 <sect1>export_users [<filename>] (9)
2851 <bf>export_users [<filename>]</bf> Export the users database to ascii
2855 Export the users database to a file in ascii format. If no filename
2856 is given then it will export the file to /spider/data/user_asc.
2858 If the file already exists it will be renamed to <filename>.o. In fact
2859 up to 5 generations of the file can be kept each one with an extra 'o' on the
2862 BE WARNED: this will write to any file you have write access to. No check is
2863 made on the filename (if any) that you specify.
2864 <sect1>filtering... (0)
2868 <bf>filtering...</bf> Filtering things in DXSpider
2872 There are a number of things you can filter in the DXSpider system. They
2873 all use the same general mechanism.
2875 In general terms you can create a 'reject' or an 'accept' filter which
2876 can have up to 10 lines in it. You do this using, for example:-
2883 where ..... are the specific commands for that type of filter. There
2884 are filters for spots, wwv, announce, wcy and (for sysops)
2885 connects. See each different accept or reject command reference for
2888 There is also a command to clear out one or more lines in a filter and
2889 one to show you what you have set. They are:-
2902 There is clear/xxxx command for each type of filter.
2904 For now we are going to use spots for the examples, but you can apply
2905 the principles to all types of filter.
2907 There are two main types of filter 'accept' or 'reject'; which you use
2908 depends entirely on how you look at the world and what is least
2909 writing to achieve what you want. Each filter has 10 lines (of any
2910 length) which are tried in order. If a line matches then the action
2911 you have specified is taken (ie reject means ignore it and accept
2914 The important thing to remember is that if you specify a 'reject'
2915 filter (all the lines in it say 'reject/spots' (for instance)) then if
2916 a spot comes in that doesn't match any of the lines then you will get
2917 it BUT if you specify an 'accept' filter then any spots that don't
2918 match are dumped. For example if I have a one line accept filter:-
2921 accept/spots on vhf and (by_zone 14,15,16 or call_zone 14,15,16)
2924 then automatically you will ONLY get VHF spots from or to CQ zones 14
2925 15 and 16. If you set a reject filter like:
2928 reject/spots on hf/cw
2931 Then you will get everything EXCEPT HF CW spots, If you am interested in IOTA
2932 and will work it even on CW then you could say:-
2935 reject/spots on hf/cw and not info iota
2938 But in that case you might only be interested in iota and say:-
2941 accept/spots not on hf/cw or info iota
2944 which is exactly the same. You should choose one or the other until
2945 you are confortable with the way it works. Yes, you can mix them
2946 (actually you can have an accept AND a reject on the same line) but
2947 don't try this at home until you can analyse the results that you get
2948 without ringing up the sysop for help.
2950 Another useful addition now is filtering by US state
2953 accept/spots by_state VA,NH,RI,ME
2956 You can arrange your filter lines into logical units, either for your
2957 own understanding or simply convenience. I have one set frequently:-
2960 reject/spots 1 on hf/cw
2961 reject/spots 2 on 50000/1400000 not (by_zone 14,15,16 or call_zone 14,15,16)
2964 What this does is to ignore all HF CW spots (being a class B I can't
2965 read any CW and couldn't possibly be interested in HF :-) and also
2966 rejects any spots on VHF which don't either originate or spot someone
2969 This is an exmaple where you would use the line number (1 and 2 in
2970 this case), if you leave the digit out, the system assumes '1'. Digits
2971 '0'-'9' are available.
2973 You can leave the word 'and' out if you want, it is implied. You can
2974 use any number of brackets to make the 'expression' as you want
2975 it. There are things called precedence rules working here which mean
2976 that you will NEED brackets in a situation like line 2 because,
2977 without it, will assume:-
2980 (on 50000/1400000 and by_zone 14,15,16) or call_zone 14,15,16
2983 annoying, but that is the way it is. If you use OR - use
2984 brackets. Whilst we are here CASE is not important. 'And BY_Zone' is
2987 If you want to alter your filter you can just redefine one or more
2988 lines of it or clear out one line. For example:-
2991 reject/spots 1 on hf/ssb
3000 To remove the filter in its entirty:-
3006 There are similar CLEAR commands for the other filters:-
3016 Once you are happy with the results you get, you may like to experiment.
3018 my example that filters hf/cw spots and accepts vhf/uhf spots from EU
3019 can be written with a mixed filter, eg:
3024 acc/spot 2 on 50000/1400000 and (by_zone 14,15,16 or call_zone 14,15,16)
3027 each filter slot actually has a 'reject' slot and an 'accept'
3028 slot. The reject slot is executed BEFORE the accept slot.
3030 It was mentioned earlier that after a reject test that doesn't match,
3031 the default for following tests is 'accept', the reverse is true for
3032 'accept'. In the example what happens is that the reject is executed
3033 first, any non hf/cw spot is passed to the accept line, which lets
3034 thru everything else on HF.
3036 The next filter line lets through just VHF/UHF spots from EU.
3037 <sect1>forward/latlong <node_call> (8)
3041 <bf>forward/latlong <node_call></bf> Send latitude and longitude information to another cluster
3045 This command sends all the latitude and longitude information that your
3046 cluster is holding against callsigns. One advantage of recieving this
3047 information is that more locator information is held by you. This
3048 means that more locators are given on the DX line assuming you have
3049 SET/DXGRID enabled. This could be a LOT of information though, so
3050 it is not recommended on slow links.
3051 <sect1>forward/opernam <call> (1)
3055 <bf>forward/opernam <call></bf> Send out information on this <call> to all clusters
3059 This command sends out any information held in the user file which can
3060 be broadcast in PC41 protocol packets. This information is Name, QTH, Location
3061 and Homenode. PC41s are only sent for the information that is available.
3067 <bf>help</bf> The HELP Command
3071 HELP is available for a number of commands. The syntax is:-
3077 Where <cmd> is the name of the command you want help on.
3079 All commands can be abbreviated, so SHOW/DX can be abbreviated
3080 to SH/DX, ANNOUNCE can be shortened to AN and so on.
3082 Look at the APROPOS <string> command which will search the help database
3083 for the <string> you specify and give you a list of likely commands
3084 to look at with HELP.
3085 <sect1>init <node> (5)
3089 <bf>init <node></bf> Re-initialise a link to an AK1A compatible node
3093 This command attempts to re-initialise a link to a (usually) AK1A node
3094 that has got confused, usually by a protocol loop of some kind. It may
3095 work - but you usually will be better off simply disconnecting it (or
3096 better, if it is a real AK1A node, doing an RCMD <node> DISC/F <your
3099 Best of luck - you will need it.
3109 As a sysop you can kill any message on the system.
3110 <sect1>kill <from msgno>-<to msgno> (0)
3114 <bf>kill <from msgno>-<to msgno></bf> Delete a range of messages
3118 <sect1>kill <from>-<to> (5)
3122 <bf>kill <from>-<to></bf> Remove a range of messages from the system
3126 <sect1>kill <msgno> [<msgno..] (0)
3130 <bf>kill <msgno> [<msgno..]</bf> Delete a message from the local system
3134 <sect1>kill <msgno> [<msgno> ...] (0)
3138 <bf>kill <msgno> [<msgno> ...]</bf> Remove or erase a message from the system
3142 You can get rid of any message to or originating from your callsign using
3143 this command. You can remove more than one message at a time.
3144 <sect1>kill expunge <msgno> [<msgno..] (6)
3148 <bf>kill expunge <msgno> [<msgno..]</bf> Expunge a message
3152 Deleting a message using the normal KILL commands only marks that message
3153 for deletion. The actual deletion only happens later (usually two days later).
3155 The KILL EXPUNGE command causes the message to be truly deleted more or less
3158 It otherwise is used in the same way as the KILL command.
3159 <sect1>kill from <call> (5)
3163 <bf>kill from <call></bf> Remove all messages from a callsign
3167 <sect1>kill full <msgno> [<msgno..] (5)
3171 <bf>kill full <msgno> [<msgno..]</bf> Delete a message from the whole cluster
3175 Delete a message from the local system. You will only be able to
3176 delete messages that you have originated or been sent (unless you are
3183 Will delete all the messages that you own between msgnos 1234 and 1255.
3189 will delete all the messages from g1tlh (if you are g1tlh). Similarly:
3195 will delete all messages to g1tlh.
3201 will delete a message (usually a 'bulletin') from the whole cluster system.
3203 This uses the subject field, so any messages that have exactly the
3204 same subject will be deleted. Beware!
3205 <sect1>kill full <msgno> [<msgno] (5)
3209 <bf>kill full <msgno> [<msgno]</bf> Remove a message from the entire cluster
3213 Remove this message from the entire cluster system as well as your node.
3214 <sect1>kill to <call> (5)
3218 <bf>kill to <call></bf> Remove all messages to a callsign
3222 <sect1>kill from <regex> (0)
3226 <bf>kill from <regex></bf> Delete messages FROM a callsign or pattern
3230 <sect1>kill to <regex> (0)
3234 <bf>kill to <regex></bf> Delete messages TO a callsign or pattern
3242 <bf>links</bf> Show which nodes is physically connected
3246 This is a quick listing that shows which links are connected and
3247 some information about them. See WHO for a list of all connections.
3248 <sect1>load/aliases (9)
3252 <bf>load/aliases</bf> Reload the command alias table
3256 Reload the /spider/cmd/Aliases file after you have editted it. You
3257 will need to do this if you change this file whilst the cluster is
3258 running in order for the changes to take effect.
3259 <sect1>load/badmsg (9)
3263 <bf>load/badmsg</bf> Reload the bad msg table
3267 Reload the /spider/msg/badmsg.pl file if you have changed it manually whilst
3268 the cluster is running. This table contains a number of perl regular
3269 expressions which are searched for in the fields targetted of each message.
3270 If any of them match then that message is immediately deleted on receipt.
3271 <sect1>load/badwords (9)
3275 <bf>load/badwords</bf> Reload the bad words table
3279 Reload the /spider/data/badwords file if you have changed it manually whilst
3280 the cluster is running. This file contains a list of words which, if found
3281 on certain text portions of PC protocol, will cause those protocol frames
3282 to be rejected. It will all put out a message if any of these words are
3283 used on the announce, dx and talk commands. The words can be one or
3284 more on a line, lines starting with '#' are ignored.
3285 <sect1>load/bands (9)
3289 <bf>load/bands</bf> Reload the band limits table
3293 Reload the /spider/data/bands.pl file if you have changed it manually whilst
3294 the cluster is running.
3295 <sect1>load/cmd_cache (9)
3299 <bf>load/cmd_cache</bf> Reload the automatic command cache
3303 Normally, if you change a command file in the cmd or local_cmd tree it
3304 will automatially be picked up by the cluster program. Sometimes it
3305 can get confused if you are doing a lot of moving commands about or
3306 delete a command in the local_cmd tree and want to use the normal one
3307 again. Execute this command to reset everything back to the state it
3308 was just after a cluster restart.
3309 <sect1>load/forward (9)
3313 <bf>load/forward</bf> Reload the msg forwarding routing table
3317 Reload the /spider/msg/forward.pl file if you have changed it
3318 manually whilst the cluster is running.
3319 <sect1>load/keps (5)
3323 <bf>load/keps</bf> Load new keps data
3327 <sect1>load/keps [nn] (5)
3331 <bf>load/keps [nn]</bf> Load new keps data from message
3335 If there is no message number then reload the current Keps data from
3336 the Keps.pm data file. You create this file by running
3339 /spider/perl/convkeps.pl <filename>
3342 on a file containing NASA 2 line keps as a message issued by AMSAT.
3344 If there is a message number, then it will take the message, run
3345 convkeps.pl on it and then load the data, all in one step.
3347 These messages are sent to ALL by GB7DJK (and others) from time to time.
3348 <sect1>load/messages (9)
3352 <bf>load/messages</bf> Reload the system messages file
3356 If you change the /spider/perl/Messages file (usually whilst
3357 fiddling/writing new commands) you can have them take effect during a
3358 cluster session by executing this command. You need to do this if get
3361 unknown message 'xxxx' in lang 'en'
3362 <sect1>load/prefixes (9)
3366 <bf>load/prefixes</bf> Reload the prefix table
3370 Reload the /spider/data/prefix_data.pl file if you have changed it
3371 manually whilst the cluster is running.
3372 <sect1>merge <node> [<no spots>/<no wwv>] (5)
3376 <bf>merge <node> [<no spots>/<no wwv>]</bf> Ask for the latest spots and WWV
3380 MERGE allows you to bring your spot and wwv database up to date. By default
3381 it will request the last 10 spots and 5 WWVs from the node you select. The
3382 node must be connected locally.
3384 You can request any number of spots or wwv and although they will be appended
3385 to your databases they will not duplicate any that have recently been added
3386 (the last 2 days for spots and last month for WWV data).
3387 <sect1>msg <cmd> <msgno> [data ... ] (9)
3391 <bf>msg <cmd> <msgno> [data ... ]</bf> Alter various message parameters
3395 Alter message parameters like To, From, Subject, whether private or bulletin
3396 or return receipt (RR) is required or whether to keep this message from timing
3400 MSG TO <msgno> <call> - change TO callsign to <call>
3401 MSG FRom <msgno> <call> - change FROM callsign to <call>
3402 MSG PRrivate <msgno> - set private flag
3403 MSG NOPRrivate <msgno> - unset private flag
3404 MSG RR <msgno> - set RR flag
3405 MSG NORR <msgno> - unset RR flag
3406 MSG KEep <msgno> - set the keep flag (message won't be deleted ever)
3407 MSG NOKEep <msgno> - unset the keep flag
3408 MSG SUbject <msgno> <new> - change the subject to <new>
3409 MSG WAittime <msgno> - remove any waitting time for this message
3410 MSG NOREad <msgno> - mark message as unread
3411 MSG REad <msgno> - mark message as read
3412 MSG QUeue - queue any outstanding bulletins
3413 MSG QUeue 1 - queue any outstanding private messages
3416 You can look at the status of a message by using:-
3419 STAT/MSG <msgno>
3422 This will display more information on the message than DIR does.
3424 <sect1>pc <call> <text> (8)
3428 <bf>pc <call> <text></bf> Send arbitrary text to a connected callsign
3432 Send some arbitrary text to a locally connected callsign. No
3433 processing is done on the text. This command allows you to send PC
3434 Protocol to unstick things if problems arise (messages get stuck
3438 pc gb7djk PC33^GB7TLH^GB7DJK^400^
3442 pc G1TLH Try doing that properly!!!
3445 Send any text you like to the callsign requested. This is used mainly to send
3446 PC protocol to connected nodes either for testing or to unstick things.
3448 You can also use in the same way as a talk command to a connected user but
3449 without any processing, added of "from <blah> to <blah" or whatever.
3451 <sect1>ping <node call> (1)
3455 <bf>ping <node call></bf> Check the link quality between nodes
3459 This command allows you to send a frame to another cluster node on
3460 the network and get a return frame. The time it takes to do this
3461 is a good indication of the quality of the link. The actual time
3462 it takes is output to the console in seconds.
3463 Any visible cluster node can be PINGed.
3464 <sect1>rcmd <node call> <cmd> (1)
3468 <bf>rcmd <node call> <cmd></bf> Send a command to another DX Cluster
3472 This command allows you to send nearly any command to another DX Cluster
3473 node that is connected to the system.
3475 Whether you get any output is dependant on a) whether the other system knows
3476 that the node callsign of this cluster is in fact a node b) whether the
3477 other system is allowing RCMDs from this node and c) whether you have
3478 permission to send this command at all.
3483 <bf>read</bf> Read the next unread personal message addressed to you
3487 <sect1>read <msgno> (0)
3491 <bf>read <msgno></bf> Read the specified message
3495 You can read any messages that are sent as 'non-personal' and also any
3496 message either sent by or sent to your callsign.
3505 As a sysop you may read any message on the system
3510 <bf>reject</bf> Set a filter to reject something
3514 Create a filter to reject something
3516 There are 2 types of filter, accept and reject. See HELP FILTERING for more
3518 <sect1>reject/announce <call> [input] [0-9] <pattern> (8)
3522 <bf>reject/announce <call> [input] [0-9] <pattern></bf> Announce filter sysop version
3526 This version allows a sysop to set a filter for a callsign as well as the
3527 default for nodes and users eg:-
3531 reject/ann input node_default by G,M,2
3532 reject/ann user_default by G,M,2
3535 <sect1>reject/announce [0-9] <pattern> (0)
3539 <bf>reject/announce [0-9] <pattern></bf> Set a 'reject' filter line for announce
3543 Create an 'reject this announce' line for a filter.
3545 A reject filter line means that if the announce matches this filter it is
3546 passed onto the user. See HELP FILTERING for more info. Please read this
3547 to understand how filters work - it will save a lot of grief later on.
3549 You can use any of the following things in this line:-
3552 info <string> eg: iota or qsl
3553 by <prefixes> eg: G,M,2
3554 origin <prefixes>
3555 origin_dxcc <prefixes or numbers> eg: 61,62 (from eg: sh/pre G)
3556 origin_itu <prefixes or numbers> or: G,GM,GW
3557 origin_zone <prefixes or numbers>
3558 origin_state <states> eg: VA,NH,RI,ME
3559 by_dxcc <prefixes or numbers>
3560 by_itu <prefixes or numbers>
3561 by_zone <prefixes or numbers>
3562 by_state <states> eg: VA,NH,RI,ME
3563 channel <prefixes>
3564 wx 1 filter WX announces
3565 dest <prefixes> eg: 6MUK,WDX (distros)
3571 rej/ann by_zone 14,15,16 and not by G,M,2
3574 You can use the tag 'all' to reject everything eg:
3580 but this probably for advanced users...
3581 <sect1>reject/route <call> [0-9] <pattern> (8)
3585 <bf>reject/route <call> [0-9] <pattern></bf> Set an 'reject' filter line for routing
3589 Create an 'reject this routing PC Protocol' line for a filter.
3591 An reject filter line means that if a PC16/17/19/21/24/41/50 matches this filter
3592 it is NOT passed thru that interface. See HELP FILTERING for more info. Please
3593 read this to understand how filters work - it will save a lot of grief later on.
3595 You can use any of the following things in this line:-
3598 call <prefixes> the callsign of the thingy
3599 call_dxcc <prefixes or numbers> eg: 61,62 (from eg: sh/pre G)
3600 call_itu <prefixes or numbers> or: G,GM,GW
3601 call_zone <prefixes or numbers>
3602 call_state <states> eg: VA,NH,RI,ME
3603 origin <prefixes> really the interface it came in on
3604 origin_dxcc <prefixes or numbers> eg: 61,62 (from eg: sh/pre G)
3605 origin_itu <prefixes or numbers> or: G,GM,GW
3606 origin_zone <prefixes or numbers>
3607 origin_state <states> eg: VA,NH,RI,ME
3613 rej/route gb7djk call_dxcc 61,38 (everything except UK+EIRE nodes)
3616 You can use the tag 'all' to reject everything eg:
3619 rej/route all (equiv to [very] restricted mode)
3622 as with ACCEPT/ROUTE 'by' is now a synonym for 'call'.
3623 <sect1>reject/spots <call> [input] [0-9] <pattern> (8)
3627 <bf>reject/spots <call> [input] [0-9] <pattern></bf> Spot filter sysop version
3631 This version allows a sysop to set a filter for a callsign as well as the
3632 default for nodes and users eg:-
3635 reject/spot db0sue-7 1 by_zone 14,15,16
3636 reject/spot node_default all
3637 set/hops node_default 10
3641 reject/spot user_default by G,M,2
3644 <sect1>reject/spots [0-9] <pattern> (0)
3648 <bf>reject/spots [0-9] <pattern></bf> Set a 'reject' filter line for spots
3652 Create a 'reject this spot' line for a filter.
3654 A reject filter line means that if the spot matches this filter it is
3655 dumped (not passed on). See HELP FILTERING for more info. Please read this
3656 to understand how filters work - it will save a lot of grief later on.
3658 You can use any of the following things in this line:-
3661 freq <range> eg: 0/30000 or hf or hf/cw or 6m,4m,2m
3662 on <range> same as 'freq'
3663 call <prefixes> eg: G,PA,HB9
3664 info <string> eg: iota or qsl
3666 call_dxcc <prefixes or numbers> eg: 61,62 (from eg: sh/pre G)
3667 call_itu <prefixes or numbers> or: G,GM,GW
3668 call_zone <prefixes or numbers>
3669 call_state <states> eg: VA,NH,RI,ME
3670 by_dxcc <prefixes or numbers>
3671 by_itu <prefixes or numbers>
3672 by_zone <prefixes or numbers>
3673 by_state <states> eg: VA,NH,RI,ME
3674 origin <prefixes>
3675 channel <prefixes>
3678 'call' means the callsign that has spotted 'by' whoever.
3680 For frequencies, you can use any of the band names defined in
3681 SHOW/BANDS and you can use a subband name like: cw, rtty, data, ssb -
3682 thus: hf/ssb. You can also just have a simple range like: 0/30000 -
3683 this is more efficient than saying simply: on HF (but don't get
3684 too hung up about that)
3690 rej/spot 2 on vhf and not (by_zone 14,15,16 or call_zone 14,15,16)
3693 You can use the tag 'all' to reject everything eg:
3699 but this probably for advanced users...
3700 <sect1>reject/wcy <call> [input] [0-9] <pattern> (8)
3704 <bf>reject/wcy <call> [input] [0-9] <pattern></bf> WCY filter sysop version
3708 This version allows a sysop to set a filter for a callsign as well as the
3709 default for nodes and users eg:-
3712 reject/wcy gb7djk all
3715 <sect1>reject/wcy [0-9] <pattern> (0)
3719 <bf>reject/wcy [0-9] <pattern></bf> set a 'reject' WCY filter
3723 It is unlikely that you will want to do this, but if you do then you can
3724 filter on the following fields:-
3727 by <prefixes> eg: G,M,2
3728 origin <prefixes>
3729 origin_dxcc <prefixes or numbers> eg: 61,62 (from eg: sh/pre G)
3730 origin_itu <prefixes or numbers> or: G,GM,GW
3731 origin_zone <prefixes or numbers>
3732 by_dxcc <prefixes or numbers>
3733 by_itu <prefixes or numbers>
3734 by_zone <prefixes or numbers>
3735 channel <prefixes>
3738 There are no examples because WCY Broadcasts only come from one place and
3739 you either want them or not (see UNSET/WCY if you don't want them).
3741 This command is really provided for future use.
3743 See HELP FILTER for information.
3744 <sect1>reject/wwv <call> [input] [0-9] <pattern> (8)
3748 <bf>reject/wwv <call> [input] [0-9] <pattern></bf> WWV filter sysop version
3752 This version allows a sysop to set a filter for a callsign as well as the
3753 default for nodes and users eg:-
3756 reject/wwv db0sue-7 1 by_zone 4
3757 reject/wwv node_default all
3761 reject/wwv user_default by W
3764 <sect1>reject/wwv [0-9] <pattern> (0)
3768 <bf>reject/wwv [0-9] <pattern></bf> set a 'reject' WWV filter
3772 It is unlikely that you will want to do this, but if you do then you can
3773 filter on the following fields:-
3776 by <prefixes> eg: G,M,2
3777 origin <prefixes>
3778 origin_dxcc <prefixes or numbers> eg: 61,62 (from eg: sh/pre G)
3779 origin_itu <prefixes or numbers> or: G,GM,GW
3780 origin_zone <prefixes or numbers>
3781 by_dxcc <prefixes or numbers>
3782 by_itu <prefixes or numbers>
3783 by_zone <prefixes or numbers>
3784 channel <prefixes>
3790 reject/wwv by_zone 14,15,16
3793 is probably the only useful thing to do (which will only show WWV broadcasts
3794 by stations in the US).
3796 See HELP FILTER for information.
3801 <bf>reply</bf> Reply (privately) to the last message that you have read
3805 <sect1>reply <msgno> (0)
3809 <bf>reply <msgno></bf> Reply (privately) to the specified message
3813 <sect1>reply b <msgno> (0)
3817 <bf>reply b <msgno></bf> Reply as a Bulletin to the specified message
3821 <sect1>reply noprivate <msgno> (0)
3825 <bf>reply noprivate <msgno></bf> Reply as a Bulletin to the specified message
3829 <sect1>reply rr <msgno> (0)
3833 <bf>reply rr <msgno></bf> Reply to the specified message with read receipt
3837 You can reply to a message and the subject will automatically have
3838 "Re:" inserted in front of it, if it isn't already present.
3840 You can also use all the extra qualifiers such as RR, PRIVATE,
3841 NOPRIVATE, B that you can use with the SEND command (see SEND
3842 for further details)
3843 <sect1>save [-d -t -a] <filename> "<cmd>" [...] (9)
3847 <bf>save [-d -t -a] <filename> "<cmd>" [...]</bf> Save command output to a file
3851 This sysop only cammand allows you to save the output of one or more
3852 commands to a file. For example:-
3855 save /spider/packclus/dxstats show/dxstat
3858 will save the output of the normal command "show/dxstat" to the file
3859 "dxstats" in the files area.
3861 You can have some extra flags to the save which will either
3862 date stamp or time stamp or both the filename so:-
3865 save -d /tmp/a <cmd> creates /tmp/a_6-Jan-2002
3866 save -t /tmp/a <cmd> creates /tmp/a_2301Z
3867 save -d -t /tmp/a <cmd> creates /tmp/a_6-Jan-2002_2301Z
3870 The -a flag means append to the file instead of overwriting it.
3872 You can have more than one command on the line, to do this you MUST
3873 enclose each command in double quotes (") eg:-
3876 save /tmp/a "sh/hfstats" "blank +" "sh/vhfstats"
3882 save /tmp/a "sh/hfstats","blank +","sh/vhfstats"
3885 You can only write into places that the cluster has permission for (which
3886 is that of the "sysop" user [which had BETTER NOT BE "root"]), you will
3887 need to create any directories you want to put stuff in beforehand as well.
3889 It is likely that you will want to run these commands in a crontab type
3890 situation. You would do that something like:-
3893 0 0 * * * run_cmd('save /tmp/dxstats "echo DXStat Table", "sh/dxstats"')
3896 Note that you still enclose each command with (") characters but you must
3897 enclose the entire save command in (') characters.
3899 Now in fact, this can be varied if you know what you are doing. See the
3900 admin manual for more details.
3902 <sect1>send <call> [<call> ...] (0)
3906 <bf>send <call> [<call> ...]</bf> Send a message to one or more callsigns
3910 <sect1>send copy <msgno> <call> (0)
3914 <bf>send copy <msgno> <call></bf> Send a copy of a message to someone
3918 <sect1>send noprivate <call> (0)
3922 <bf>send noprivate <call></bf> Send a message to all stations
3926 All the SEND commands will create a message which will be sent either to
3927 an individual callsign or to one of the 'bulletin' addresses.
3929 SEND <call> on its own acts as though you had typed SEND PRIVATE, that is
3930 it will mark the message as personal and send it to the cluster node that
3931 that callsign is connected to. If the <call> you have specified is in fact
3932 a known bulletin category on your node (eg: ALL) then the message should
3933 automatically become a bulletin.
3935 You can have more than one callsign in all of the SEND commands.
3937 You can have multiple qualifiers so that you can have for example:-
3940 SEND RR COPY 123 PRIVATE G1TLH G0RDI
3943 which should send a copy of message 123 to G1TLH and G0RDI and you will
3944 receive a read receipt when they have read the message.
3946 SB is an alias for SEND NOPRIVATE (or send a bulletin in BBS speak)
3947 SP is an alias for SEND PRIVATE
3949 The system will ask you for a subject. Conventionally this should be
3950 no longer than 29 characters for compatibility. Most modern cluster
3951 software should accept more.
3953 You will now be prompted to start entering your text.
3955 You finish the message by entering '/EX' on a new line. For instance:
3964 If you have started a message and you don't want to keep it then you
3965 can abandon the message with '/ABORT' on a new line, like:-
3970 oh I just can't be bothered with this
3974 If you abort the message it will NOT be sent.
3976 When you are entering the text of your message, most normal output (such
3977 as DX announcements and so on are suppressed and stored for latter display
3978 (upto 20 such lines are stored, as new ones come along, so the oldest
3981 Also, you can enter normal commands commands (and get the output
3982 immediately) whilst in the middle of a message. You do this by typing
3983 the command preceeded by a '/' character on a new line, so:-
3986 /dx g1tlh 144010 strong signal
3989 Will issue a dx annoucement to the rest of the cluster.
3991 Also, you can add the output of a command to your message by preceeding
3992 the command with '//', thus :-
3998 This will show YOU the output from SH/VHFTABLE and also store it in the
4001 You can carry on with the message until you are ready to send it.
4002 <sect1>send private <call> (0)
4006 <bf>send private <call></bf> Send a personal message
4010 <sect1>send rr <call> (0)
4014 <bf>send rr <call></bf> Send a message and ask for a read receipt
4018 <sect1>set/address <your address> (0)
4022 <bf>set/address <your address></bf> Record your postal address
4026 <sect1>set/announce (0)
4030 <bf>set/announce</bf> Allow announce messages to come out on your terminal
4034 <sect1>set/anntalk (0)
4038 <bf>set/anntalk</bf> Allow talk like announce messages on your terminal
4042 <sect1>set/arcluster <call> [<call>..] (5)
4046 <bf>set/arcluster <call> [<call>..]</bf> Make the callsign an AR-Cluster node
4050 <sect1>set/baddx <call>.. (8)
4054 <bf>set/baddx <call>..</bf> Stop callsigns in a dx spot being propagated
4058 <sect1>set/badnode <call>.. (8)
4062 <bf>set/badnode <call>..</bf> Stop spots from this node being propagated
4066 <sect1>set/badspotter <call>.. (8)
4070 <bf>set/badspotter <call>..</bf> Stop spots from this callsign being propagated
4074 <sect1>set/badword <word>.. (8)
4078 <bf>set/badword <word>..</bf> Stop things with this word being propagated
4082 <sect1>set/bbs <call> [<call>..] (5)
4086 <bf>set/bbs <call> [<call>..]</bf> Make the callsign a BBS
4094 <bf>set/beep</bf> Add a beep to DX and other messages on your terminal
4098 <sect1>set/clx <call> [<call>..] (5)
4102 <bf>set/clx <call> [<call>..]</bf> Make the callsign an CLX node
4106 <sect1>set/debug <name> (9)
4110 <bf>set/debug <name></bf> Add a debug level to the debug set
4118 <bf>set/dx</bf> Allow DX messages to come out on your terminal
4126 <bf>set/dxcq</bf> Show CQ Zones on the end of DX announcements
4130 <sect1>set/dxgrid (0)
4134 <bf>set/dxgrid</bf> Allow QRA Grid Squares on the end of DX announcements
4138 <sect1>set/dxitu (0)
4142 <bf>set/dxitu</bf> Show ITU Zones on the end of DX announcements
4146 <sect1>set/dxnet <call> [<call>..] (5)
4150 <bf>set/dxnet <call> [<call>..]</bf> Make the callsign an DXNet node
4158 <bf>set/echo</bf> Make the cluster echo your input
4162 <sect1>set/email <email> ... (0)
4166 <bf>set/email <email> ...</bf> Set email address(es) and forward your personals
4174 <bf>set/here</bf> Tell the system you are present at your terminal
4178 <sect1>set/homenode <node> (0)
4182 <bf>set/homenode <node> </bf> Set your normal cluster callsign
4186 Tell the cluster system where you normally connect to. Any Messages sent
4187 to you will normally find their way there should you not be connected.
4193 <sect1>set/hops <call> ann|spots|route|wwv|wcy <n> (8)
4197 <bf>set/hops <call> ann|spots|route|wwv|wcy <n></bf> Set hop count
4201 <sect1>set/isolate (9)
4205 <bf>set/isolate</bf> Isolate a node from the rest of the network
4209 Connect a node to your system in such a way that you are a full protocol
4210 member of its network and can see all spots on it, but nothing either leaks
4211 out from it nor goes back into from the rest of the nodes connected to you.
4213 You can potentially connect several nodes in this way.
4215 <sect1>set/language <lang> (0)
4219 <bf>set/language <lang></bf> Set the language you want to use
4223 You can select the language that you want the cluster to use. Currently
4224 the languages available are en (English), de (German), es (Spanish)
4226 <sect1>set/location <lat & long> (0)
4230 <bf>set/location <lat & long></bf> Set your latitude and longitude
4234 <sect1>set/lockout <call> (9)
4238 <bf>set/lockout <call></bf> Stop a callsign connecting to the cluster
4242 <sect1>set/logininfo (0)
4246 <bf>set/logininfo</bf> Inform when a station logs in locally
4250 <sect1>set/name <your name> (0)
4254 <bf>set/name <your name></bf> Set your name
4258 Tell the system what your name is eg:-
4263 <sect1>set/node <call> [<call>..] (5)
4267 <bf>set/node <call> [<call>..]</bf> Make the callsign an AK1A cluster
4271 Tell the system that the call(s) are to be treated as AK1A cluster and
4272 fed PC Protocol rather normal user commands.
4273 <sect1>set/obscount <count> <call> (8)
4277 <bf>set/obscount <count> <call></bf> Set the 'pump-up' obscelence PING counter
4281 From 1.35 onwards neighbouring nodes are pinged at regular intervals (see
4282 SET/PINGINTERVAL), usually 300 seconds or 5 minutes. There is a 'pump-up'
4283 counter which is decremented on every outgoing ping and then reset to
4284 the 'obscount' value on every incoming ping. The default value of this
4287 What this means is that a neighbouring node will be pinged twice at
4288 (default) 300 second intervals and if no reply has been heard just before
4289 what would be the third attempt, that node is disconnected.
4291 If a ping is heard then the obscount is reset to the full value. Using
4292 default values, if a node has not responded to a ping within 15 minutes,
4295 You can set this parameter between 1 and 9.
4297 It is STRONGLY recommended that you don't change the default.
4298 <sect1>set/page <lines per page> (0)
4302 <bf>set/page <lines per page></bf> Set the lines per page
4306 Tell the system how many lines you wish on a page when the number of line
4307 of output from a command is more than this. The default is 20. Setting it
4308 explicitly to 0 will disable paging.
4314 The setting is stored in your user profile.
4315 <sect1>set/password (0)
4319 <bf>set/password</bf> Set your own password
4323 This command only works for a 'telnet' user (currently). It will
4324 only work if you have a password already set. This initial password
4325 can only be set by the sysop.
4327 When you execute this command it will ask you for your old password,
4328 then ask you to type in your new password twice (to make sure you
4329 get it right). You may or may not see the data echoed on the screen
4330 as you type, depending on the type of telnet client you have.
4331 <sect1>set/password <callsign> <string> (9)
4335 <bf>set/password <callsign> <string></bf> Set a users password
4339 The password for a user can only be set by a full sysop. The string
4340 can contain any characters.
4342 The way this field is used depends on context. If it is being used in
4343 the SYSOP command context then you are offered 5 random numbers and you
4344 have to supply the corresponding letters. This is now mainly for ax25
4347 If it is being used on incoming telnet connections then, if a password
4351 set/var $main::passwdreq = 1
4354 command is executed in the startup script, then a password prompt is
4355 given after the normal 'login: ' prompt.
4356 <sect1>set/pinginterval <time> <nodecall> (9)
4360 <bf>set/pinginterval <time> <nodecall></bf> Set ping time to neighbouring nodes
4364 As from release 1.35 all neighbouring nodes are pinged at regular intervals
4365 in order to determine the rolling quality of the link and, in future, to
4366 affect routing decisions. The default interval is 300 secs or 5 minutes.
4368 You can use this command to set a different interval. Please don't.
4370 But if you do the value you enter is treated as minutes up 30 and seconds
4371 for numbers greater than that.
4373 This is used also to help determine when a link is down at the far end
4374 (as certain cluster software doesn't always notice), see SET/OBSCOUNT
4375 for more information.
4377 If you must change it (and it may be useful for internet connected nodes
4378 on dynamic IP addresses that go away after a set time of usage) the time
4379 can be specified as:-
4382 5 which if less than 30 is converted to minutes otherwise is
4383 taken as the no of seconds between pings.
4389 Please be aware that this causes traffic to occur on the link, setting
4390 this value too low may annoy your neighbours beyond the point of
4393 You can switch this off by setting it to 0.
4394 <sect1>set/privilege <n> <call> [<call..] (9)
4398 <bf>set/privilege <n> <call> [<call..]</bf> Set privilege level on a call
4402 Set the privilege level on a callsign. The privilege levels that pertain
4403 to commands are as default:-
4406 1 - allow remote nodes normal user RCMDs
4407 5 - various privileged commands (including shutdown, but not disc-
4408 connect), the normal level for another node.
4409 8 - more privileged commands (including disconnect)
4410 9 - local sysop privilege. DO NOT SET ANY REMOTE USER OR NODE TO THIS
4413 If you are a sysop and you come in as a normal user on a remote connection
4414 your privilege will automatically be set to 0.
4415 <sect1>set/prompt <string> (0)
4419 <bf>set/prompt <string></bf> Set your prompt to <string>
4423 <sect1>set/qra <locator> (0)
4427 <bf>set/qra <locator></bf> Set your QRA Grid locator
4431 Tell the system what your QRA (or Maidenhead) locator is. If you have not
4432 done a SET/LOCATION then your latitude and longitude will be set roughly
4433 correctly (assuming your locator is correct ;-). For example:-
4438 <sect1>set/qth <your qth> (0)
4442 <bf>set/qth <your qth></bf> Set your QTH
4446 Tell the system where you are. For example:-
4448 SET/QTH East Dereham, Norfolk
4451 <sect1>set/register <call> ... (9)
4455 <bf>set/register <call> ...</bf> Mark a user as registered
4459 <sect1>set/spider <call> [<call>..] (5)
4463 <bf>set/spider <call> [<call>..]</bf> Make the callsign an DXSpider node
4467 Tell the system that the call(s) are to be treated as DXSpider node and
4468 fed new style DX Protocol rather normal user commands.
4469 <sect1>set/sys_location <lat & long> (9)
4473 <bf>set/sys_location <lat & long></bf> Set your cluster latitude and longitude
4477 In order to get accurate headings and such like you must tell the system
4478 what your latitude and longitude is. If you have not yet done a SET/QRA
4479 then this command will set your QRA locator for you. For example:-
4481 SET/LOCATION 52 22 N 0 57 E
4484 <sect1>set/sys_qra <locator> (9)
4488 <bf>set/sys_qra <locator></bf> Set your cluster QRA Grid locator
4496 <bf>set/talk</bf> Allow TALK messages to come out on your terminal
4500 <sect1>set/usdb <call> <state> <city> (9)
4504 <bf>set/usdb <call> <state> <city></bf> add/update a US DB callsign
4508 This command allows you to add or alter a callsign in the US state
4509 database. Use with extreme caution. Anything you do here will be
4510 overwritten by any weekly updates that affect this callsign
4513 set/usdb g1tlh nh downtown rindge
4516 see also DELETE/USDB
4517 <sect1>set/usstate (0)
4521 <bf>set/usstate</bf> Allow US State info on the end of DX announcements
4529 <bf>set/wcy</bf> Allow WCY messages to come out on your terminal
4537 <bf>set/wwv</bf> Allow WWV messages to come out on your terminal
4545 <bf>set/wx</bf> Allow WX messages to come out on your terminal
4549 <sect1>show/baddx (1)
4553 <bf>show/baddx</bf> Show all the bad dx calls in the system
4557 Display all the bad dx callsigns in the system, see SET/BADDX
4558 for more information.
4559 <sect1>show/badnode (1)
4563 <bf>show/badnode</bf> Show all the bad nodes in the system
4567 Display all the bad node callsigns in the system, see SET/BADNODE
4568 for more information.
4569 <sect1>show/badspotter (1)
4573 <bf>show/badspotter</bf> Show all the bad spotters in the system
4577 Display all the bad spotter's callsigns in the system, see SET/BADSPOTTER
4578 for more information.
4579 <sect1>show/badword (1)
4583 <bf>show/badword</bf> Show all the bad words in the system
4587 Display all the bad words in the system, see SET/BADWORD
4588 for more information.
4589 <sect1>show/configuration [<node>] (0)
4593 <bf>show/configuration [<node>]</bf> Show all the nodes and users visible
4597 This command allows you to see all the users that can be seen
4598 and the nodes to which they are connected.
4600 This command is normally abbreviated to: sh/c
4602 Normally, the list returned will be just for the nodes from your
4603 country (because the list otherwise will be very long).
4609 will produce a complete list of all nodes.
4611 BE WARNED: the list that is returned can be VERY long
4613 It is possible to supply a node or part of a prefix and you will get
4614 a list of the users for that node or list of nodes starting with
4625 <sect1>show/configuration/node (0)
4629 <bf>show/configuration/node</bf> Show all the nodes connected locally
4633 Show all the nodes connected to this node.
4634 <sect1>show/connect (1)
4638 <bf>show/connect</bf> Show all the active connections
4642 This command shows information on all the active connections known to
4643 the node. This command gives slightly more information than WHO.
4644 <sect1>show/contest <year and month> (0)
4648 <bf>show/contest <year and month></bf> Show all the contests for a month
4652 Show all known contests which are maintained at http://www.sk3bg.se/contest/
4653 for a particular month or year. The format is reasonably flexible.
4661 <sect1>show/date [<prefix>|<callsign>] (0)
4665 <bf>show/date [<prefix>|<callsign>]</bf> Show the local time
4669 This is very nearly the same as SHOW/TIME, the only difference the format
4670 of the date string if no arguments are given.
4672 If no prefixes or callsigns are given then this command returns the local
4673 time and UTC as the computer has it right now. If you give some prefixes
4674 then it will show UTC and UTC + the local offset (not including DST) at
4675 the prefixes or callsigns that you specify.
4676 <sect1>show/db0sdx <callsign> (0)
4680 <bf>show/db0sdx <callsign></bf> Show QSL infomation from DB0SDX database
4684 This command queries the DB0SDX QSL server on the internet
4685 and returns any information available for that callsign. This service
4686 is provided for users of this software by http://www.qslinfo.de.
4688 See also SHOW/QRZ, SHOW/WM7D.
4689 <sect1>show/debug (9)
4693 <bf>show/debug</bf> Show what levels of debug information you are logging
4701 <bf>show/dx</bf> Interrogate the spot database
4705 If you just type SHOW/DX you will get the last so many spots
4706 (sysop configurable, but usually 10).
4708 In addition you can add any number of these commands in very nearly
4709 any order to the basic SHOW/DX command, they are:-
4712 on <band> - eg 160m 20m 2m 23cm 6mm
4713 on <region> - eg hf vhf uhf shf (see SHOW/BANDS)
4714 on <from>/<to> - eg 1000/4000 14000-30000 (in Khz)
4715 <from>-<to>
4719 <number> - the number of spots you want
4720 <from>-<to> - <from> spot no <to> spot no in the selected list
4721 <from>/<to>
4725 <prefix> - for a spotted callsign beginning with <prefix>
4726 *<suffix> - for a spotted callsign ending in <suffix>
4727 *<string>* - for a spotted callsign containing <string>
4731 day <number> - starting <number> days ago
4732 day <from>-<to> - <from> days <to> days ago
4733 <from>/<to>
4737 info <text> - any spots containing <text> in the info or remarks
4741 by <call> - any spots spotted by <call> (spotter <call> is the
4746 qsl - this automatically looks for any qsl info on the call
4747 held in the spot database.
4751 iota [<iota>] - If the iota island number is missing it will look for
4752 the string iota and anything which looks like an iota
4753 island number. If you specify then it will look for
4758 qra [<locator>] - this will look for the specific locator if you specify
4759 one or else anything that looks like a locator.
4763 dxcc - treat the prefix as a 'country' and look for spots
4764 from that country regardless of actual prefix.
4769 You can also use this with the 'by' keyword so
4779 SH/DX on 20m info iota
4780 SH/DX 9a on vhf day 30
4786 SH/DX dxcc oq2 by w dxcc
4789 <sect1>show/dxcc <prefix> (0)
4793 <bf>show/dxcc <prefix></bf> Interrogate the spot database by country
4797 This command takes the <prefix> (which can be a full or partial
4798 callsign if desired), looks up which internal country number it is
4799 and then displays all the spots as per SH/DX for that country.
4801 This is now an alias for 'SHOW/DX DXCC'
4803 The options for SHOW/DX also apply to this command.
4808 SH/DXCC W on 20m iota
4811 This can be done with the SHOW/DX command like this:-
4815 SH/DX dxcc w on 20m iota
4818 <sect1>show/dxqsl <callsign> (0)
4822 <bf>show/dxqsl <callsign></bf> Show any QSL info gathered from spots
4826 The node collects information from the comment fields in spots (things
4827 like 'VIA EA7WA' or 'QSL-G1TLH') and stores these in a database.
4829 This command allows you to interrogate that database and if the callsign
4830 is found will display the manager(s) that people have spotted. This
4831 information is NOT reliable, but it is normally reasonably accurate if
4832 it is spotted enough times.
4840 You can check the raw input spots yourself with:-
4846 This gives you more background information.
4847 <sect1>show/dxstats [days] [date] (0)
4851 <bf>show/dxstats [days] [date]</bf> Show the DX Statistics
4855 Show the total DX spots for the last <days> no of days (default is 31),
4856 starting from a <date> (default: today).
4857 <sect1>show/files [<filearea> [<string>]] (0)
4861 <bf>show/files [<filearea> [<string>]]</bf> List the contents of a filearea
4865 SHOW/FILES on its own will show you a list of the various fileareas
4866 available on the system. To see the contents of a particular file
4869 SH/FILES <filearea>
4871 where <filearea> is the name of the filearea you want to see the
4874 You can also use shell globbing characters like '*' and '?' in a
4875 string to see a selection of files in a filearea eg:-
4877 SH/FILES bulletins arld*
4880 See also TYPE - to see the contents of a file.
4881 <sect1>show/filter (0)
4885 <bf>show/filter</bf> Show the contents of all the filters you have set
4889 Show the contents of all the filters that are set. This command displays
4890 all the filters set - for all the various categories.
4891 <sect1>show/hfstats [days] [date] (0)
4895 <bf>show/hfstats [days] [date]</bf> Show the HF DX Statistics
4899 Show the HF DX spots breakdown by band for the last <days> no of days
4900 (default is 31), starting from a <date> (default: today).
4901 <sect1>show/hftable [days] [date] [prefix ...] (0)
4905 <bf>show/hftable [days] [date] [prefix ...]</bf> Show the HF DX Spotter Table
4909 Show the HF DX Spotter table for the list of prefixes for the last
4910 <days> no of days (default is 31), starting from a <date> (default: today).
4912 If there are no prefixes then it will show the table for your country.
4914 Remember that some countries have more than one "DXCC country" in them
4915 (eg G :-), to show them (assuming you are not in G already which is
4916 specially treated in the code) you must list all the relevant prefixes
4919 sh/hftable g gm gd gi gj gw gu
4922 Note that the prefixes are converted into country codes so you don't have
4923 to list all possible prefixes for each country.
4925 If you want more or less days than the default simply include the
4926 number you require:-
4932 If you want to start at a different day, simply add the date in some
4936 sh/hftable 2 25nov02
4937 sh/hftable 2 25-nov-02
4939 sh/hftable 2 25/11/02
4942 This will show the stats for your DXCC for that CQWW contest weekend.
4944 You can specify either prefixes or full callsigns (so you can see how you
4945 did against all your mates). You can also say 'all' which will then print
4946 the worldwide statistics.
4952 <sect1>show/hops <call> [ann|spots|route|wcy|wwv] (8)
4956 <bf>show/hops <call> [ann|spots|route|wcy|wwv]</bf> Show the hop counts for a node
4960 This command shows the hop counts set up for a node. You can specify
4961 which category you want to see. If you leave the category out then
4962 all the categories will be listed.
4964 <sect1>show/isolate (1)
4968 <bf>show/isolate</bf> Show list of ISOLATED nodes
4972 <sect1>show/lockout <prefix>|all (9)
4976 <bf>show/lockout <prefix>|all</bf> Show the list of locked out or excluded callsigns
4980 <sect1>show/log [<callsign>] (8)
4984 <bf>show/log [<callsign>]</bf> Show excerpts from the system log
4988 This command outputs a short section of the system log. On its own
4989 it will output a general logfile. With the optional callsign it will
4990 show output from the log associated with that callsign.
4991 <sect1>show/moon [ndays] [<prefix>|<callsign>] (0)
4995 <bf>show/moon [ndays] [<prefix>|<callsign>]</bf> Show Moon rise and set times
4999 Show the Moon rise and set times for a (list of) prefixes or callsigns,
5000 together with the azimuth and elevation of the sun currently at those
5003 If you don't specify any prefixes or callsigns, it will show the times for
5004 your QTH (assuming you have set it with either SET/LOCATION or SET/QRA),
5005 together with the current azimuth and elevation.
5007 In addition, it will show the illuminated fraction of the moons disk.
5009 If all else fails it will show the Moonrise and set times for the node
5010 that you are connected to.
5019 You can also use this command to see into the past or the future, so
5020 if you want to see yesterday's times then do:-
5026 or in three days time:-
5032 Upto 366 days can be checked both in the past and in the future.
5034 Please note that the rise and set times are given as the UT times of rise and
5035 set on the requested UT day.
5036 <sect1>show/muf <prefix> [<hours>][long] (0)
5040 <bf>show/muf <prefix> [<hours>][long]</bf> Show the likely propagation to a prefix
5044 This command allow you to estimate the likelihood of you contacting
5045 a station with the prefix you have specified. The output assumes a modest
5046 power of 20dBW and receiver sensitivity of -123dBm (about 0.15muV/10dB SINAD)
5048 The result predicts the most likely operating frequencies and signal
5049 levels for high frequency (shortwave) radio propagation paths on
5050 specified days of the year and hours of the day. It is most useful for
5051 paths between 250 km and 6000 km, but can be used with reduced accuracy
5052 for paths shorter or longer than this.
5054 The command uses a routine MINIMUF 3.5 developed by the U.S. Navy and
5055 used to predict the MUF given the predicted flux, day of the year,
5056 hour of the day and geographic coordinates of the transmitter and
5057 receiver. This routine is reasonably accurate for the purposes here,
5058 with a claimed RMS error of 3.8 MHz, but much smaller and less complex
5059 than the programs used by major shortwave broadcasting organizations,
5060 such as the Voice of America.
5062 The command will display some header information detailing its
5063 assumptions, together with the locations, latitude and longitudes and
5064 bearings. It will then show UTC (UT), local time at the other end
5065 (LT), calculate the MUFs, Sun zenith angle at the midpoint of the path
5066 (Zen) and the likely signal strengths. Then for each frequency for which
5067 the system thinks there is a likelihood of a circuit it prints a value.
5069 The value is currently a likely S meter reading based on the conventional
5070 6dB / S point scale. If the value has a '+' appended it means that it is
5071 1/2 an S point stronger. If the value is preceeded by an 'm' it means that
5072 there is likely to be much fading and by an 's' that the signal is likely
5075 By default SHOW/MUF will show the next two hours worth of data. You
5076 can specify anything up to 24 hours worth of data by appending the no of
5077 hours required after the prefix. For example:-
5086 RxSens: -123 dBM SFI: 159 R: 193 Month: 10 Day: 21
5087 Power : 20 dBW Distance: 6283 km Delay: 22.4 ms
5088 Location Lat / Long Azim
5089 East Dereham, Norfolk 52 41 N 0 57 E 47
5090 United-States-W 43 0 N 87 54 W 299
5091 UT LT MUF Zen 1.8 3.5 7.0 10.1 14.0 18.1 21.0 24.9 28.0 50.0
5092 18 23 11.5 -35 mS0+ mS2 S3
5093 19 0 11.2 -41 mS0+ mS2 S3
5096 indicating that you will have weak, fading circuits on top band and
5097 80m but usable signals on 40m (about S3).
5105 will get you the above display, but with the next 24 hours worth of
5113 Gives you an estimate of the long path propagation characterics. It
5114 should be noted that the figures will probably not be very useful, nor
5115 terrible accurate, but it is included for completeness.
5116 <sect1>show/newconfiguration [<node>] (0)
5120 <bf>show/newconfiguration [<node>]</bf> Show all the nodes and users visible
5124 This command allows you to see all the users that can be seen
5125 and the nodes to which they are connected.
5127 This command produces essentially the same information as
5128 SHOW/CONFIGURATION except that it shows all the duplication of
5129 any routes that might be present It also uses a different format
5130 which may not take up quite as much space if you don't have any
5133 BE WARNED: the list that is returned can be VERY long
5134 <sect1>show/newconfiguration/node (0)
5138 <bf>show/newconfiguration/node</bf> Show all the nodes connected locally
5142 Show all the nodes connected to this node in the new format.
5143 <sect1>show/node [<callsign> ...] (1)
5147 <bf>show/node [<callsign> ...]</bf> Show the type and version number of nodes
5151 Show the type and version (if connected) of the nodes specified on the
5152 command line. If no callsigns are specified then a sorted list of all
5153 the non-user callsigns known to the system will be displayed.
5154 <sect1>show/prefix <callsign> (0)
5158 <bf>show/prefix <callsign></bf> Interrogate the prefix database
5162 This command takes the <callsign> (which can be a full or partial
5163 callsign or a prefix), looks up which internal country number
5164 it is and then displays all the relevant prefixes for that country
5165 together with the internal country no, the CQ and ITU regions.
5168 <sect1>show/program (5)
5172 <bf>show/program</bf> Show the locations of all the included program modules
5176 Show the name and location where every program module was load from. This
5177 is useful for checking where you think you have loaded a .pm file from.
5178 <sect1>show/qra <lat> <long> (0)
5182 <bf>show/qra <lat> <long></bf> Convert lat/long to a QRA Grid locator
5186 This is a multipurpose command that allows you either to calculate the
5187 distance and bearing between two locators or (if only one locator is
5188 given on the command line) the distance and beraing from your station
5189 to the locator. For example:-
5196 The first example will show the distance and bearing to the locator from
5197 yourself, the second example will calculate the distance and bearing from
5198 the first locator to the second. You can use 4 or 6 character locators.
5200 It is also possible to convert a latitude and longitude to a locator by
5201 using this command with a latitude and longitude as an argument, for
5205 SH/QRA 52 41 N 0 58 E
5208 <sect1>show/qra <locator> [<locator>] (0)
5212 <bf>show/qra <locator> [<locator>]</bf> Show distance between QRA Grid locators
5216 <sect1>show/qrz <callsign> (0)
5220 <bf>show/qrz <callsign></bf> Show any callbook details on a callsign
5224 This command queries the QRZ callbook server on the internet
5225 and returns any information available for that callsign. This service
5226 is provided for users of this software by http://www.qrz.com
5228 See also SHOW/WM7D for an alternative.
5229 <sect1>show/registered [<prefix>] (9)
5233 <bf>show/registered [<prefix>]</bf> Show the registered users
5237 <sect1>show/route <callsign> ... (0)
5241 <bf>show/route <callsign> ...</bf> Show the route to the callsign
5245 This command allows you to see to which node the callsigns specified are
5246 connected. It is a sort of inverse sh/config.
5252 <sect1>show/satellite <name> [<hours> <interval>] (0)
5256 <bf>show/satellite <name> [<hours> <interval>]</bf> Show tracking data
5260 Show the tracking data from your location to the satellite of your choice
5261 from now on for the next few hours.
5263 If you use this command without a satellite name it will display a list
5264 of all the satellites known currently to the system.
5266 If you give a name then you can obtain tracking data of all the passes
5267 that start and finish 5 degrees below the horizon. As default it will
5268 give information for the next three hours for every five minute period.
5270 You can alter the number of hours and the step size, within certain
5273 Each pass in a period is separated with a row of '-----' characters
5279 SH/SAT FENGYUN1 12 2
5282 <sect1>show/station all [<regex>] (6)
5286 <bf>show/station all [<regex>]</bf> Show list of users in the system
5290 <sect1>show/station [<callsign> ..] (0)
5294 <bf>show/station [<callsign> ..]</bf> Show information about a callsign
5298 Show the information known about a callsign and whether (and where)
5299 that callsign is connected to the cluster.
5305 If no callsign is given then show the information for yourself.
5306 <sect1>show/sun [ndays] [<prefix>|<callsign>] (0)
5310 <bf>show/sun [ndays] [<prefix>|<callsign>]</bf> Show sun rise and set times
5314 Show the sun rise and set times for a (list of) prefixes or callsigns,
5315 together with the azimuth and elevation of the sun currently at those
5318 If you don't specify any prefixes or callsigns, it will show the times for
5319 your QTH (assuming you have set it with either SET/LOCATION or SET/QRA),
5320 together with the current azimuth and elevation.
5322 If all else fails it will show the sunrise and set times for the node
5323 that you are connected to.
5329 SH/SUN G1TLH K9CW ZS
5332 You can also use this command to see into the past or the future, so
5333 if you want to see yesterday's times then do:-
5339 or in three days time:-
5345 Upto 366 days can be checked both in the past and in the future.
5347 Please note that the rise and set times are given as the UT times of rise
5348 and set on the requested UT day.
5349 <sect1>show/time [<prefix>|<callsign>] (0)
5353 <bf>show/time [<prefix>|<callsign>]</bf> Show the local time
5357 If no prefixes or callsigns are given then this command returns the local
5358 time and UTC as the computer has it right now. If you give some prefixes
5359 then it will show UTC and UTC + the local offset (not including DST) at
5360 the prefixes or callsigns that you specify.
5361 <sect1>show/usdb [call ..] (0)
5365 <bf>show/usdb [call ..]</bf> Show information held on the FCC Call database
5369 Show the City and State of a Callsign held on the FCC database if
5370 his is being run on this system, eg:-
5376 <sect1>show/vhfstats [days] [date] (0)
5380 <bf>show/vhfstats [days] [date]</bf> Show the VHF DX Statistics
5384 Show the VHF DX spots breakdown by band for the last
5385 <days> no of days (default is 31), starting from a date (default: today).
5386 <sect1>show/vhftable [days] [date] [prefix ...] (0)
5390 <bf>show/vhftable [days] [date] [prefix ...]</bf> Show the VHF DX Spotter Table
5394 Show the VHF DX Spotter table for the list of prefixes for the last
5395 <days> no of days (default is 31), starting from a date (default: today).
5397 If there are no prefixes then it will show the table for your country.
5399 Remember that some countries have more than one "DXCC country" in them
5400 (eg G :-), to show them (assuming you are not in G already which is
5401 specially treated in the code) you must list all the relevant prefixes
5404 sh/vhftable g gm gd gi gj gw gu
5407 Note that the prefixes are converted into country codes so you don't have
5408 to list all possible prefixes for each country.
5410 If you want more or less days than the default simply include the
5411 number you require:-
5417 If you want to start at a different day, simply add the date in some
5421 sh/vhftable 2 25nov02
5422 sh/vhftable 2 25-nov-02
5423 sh/vhftable 2 021125
5424 sh/vhftable 2 25/11/02
5427 This will show the stats for your DXCC for that CQWW contest weekend.
5429 You can specify either prefixes or full callsigns (so you can see how you
5430 did against all your mates). You can also say 'all' which will then print
5431 the worldwide statistics.
5441 <bf>show/wcy</bf> Show last 10 WCY broadcasts
5445 <sect1>show/wcy <n> (0)
5449 <bf>show/wcy <n></bf> Show last <n> WCY broadcasts
5453 Display the most recent WCY information that has been received by the system
5455 <sect1>show/wm7d <callsign> (0)
5459 <bf>show/wm7d <callsign></bf> Show callbook details on a US callsigns
5463 This command queries the WM7D callbook server on the internet
5464 and returns any information available for that US callsign. This service
5465 is provided for users of this software by http://www.wm7d.net.
5472 <bf>show/wwv</bf> Show last 10 WWV broadcasts
5476 <sect1>show/wwv <n> (0)
5480 <bf>show/wwv <n></bf> Show last <n> WWV broadcasts
5484 Display the most recent WWV information that has been received by the system
5489 <bf>shutdown</bf> Shutdown the cluster
5493 Shutdown the cluster and disconnect all the users
5494 <sect1>spoof <call> <command> (9)
5498 <bf>spoof <call> <command></bf> Do a command as though you are another user
5502 This command is provided so that sysops can set a user's parameters without
5503 me having to write a special 'sysop' version for every user command. It
5504 allows you to pretend that you are doing the command as the user you specify.
5509 SPOOF G1TLH set/name Dirk
5510 SPOOF G1TLH set/qra JO02LQ
5513 <sect1>stat/channel [<callsign>] (5)
5517 <bf>stat/channel [<callsign>]</bf> Show the status of a channel on the cluster
5521 Show the internal status of the channel object either for the channel that
5522 you are on or else for the callsign that you asked for.
5524 Only the fields that are defined (in perl term) will be displayed.
5525 <sect1>stat/db <dbname> (5)
5529 <bf>stat/db <dbname></bf> Show the status of a database
5533 Show the internal status of a database descriptor.
5535 Depending on your privilege level you will see more or less information.
5536 This command is unlikely to be of much use to anyone other than a sysop.
5541 <bf>stat/msg</bf> Show the status of the message system
5545 <sect1>stat/msg <msgno> (1)
5549 <bf>stat/msg <msgno></bf> Show the status of a message
5553 This command shows the internal status of a message and includes information
5554 such as to whom it has been forwarded, its size, origin etc etc.
5556 If no message number is given then the status of the message system is
5558 <sect1>stat/route_node <callsign> (5)
5562 <bf>stat/route_node <callsign></bf> Show the data in a Route::Node object
5566 <sect1>stat/route_node all (5)
5570 <bf>stat/route_node all</bf> Show list of all Route::Node objects
5574 <sect1>stat/route_user <callsign> (5)
5578 <bf>stat/route_user <callsign></bf> Show the data in a Route::User object
5582 <sect1>stat/route_user all (5)
5586 <bf>stat/route_user all</bf> Show list of all Route::User objects
5590 <sect1>stat/user [<callsign>] (5)
5594 <bf>stat/user [<callsign>]</bf> Show the full status of a user
5598 Shows the full contents of a user record including all the secret flags
5601 Only the fields that are defined (in perl term) will be displayed.
5606 <bf>sysop</bf> Regain your privileges if you login remotely
5610 The system automatically reduces your privilege level to that of a
5611 normal user if you login in remotely. This command allows you to
5612 regain your normal privilege level. It uses the normal system: five
5613 numbers are returned that are indexes into the character array that is
5614 your assigned password (see SET/PASSWORD). The indexes start from
5617 You are expected to return a string which contains the characters
5618 required in the correct order. You may intersperse those characters
5619 with others to obscure your reply for any watchers. For example (and
5620 these values are for explanation :-):
5623 password = 012345678901234567890123456789
5629 aa2bbbb0ccc5ddd7xxx3n
5634 They will all match. If there is no password you will still be offered
5635 numbers but nothing will happen when you input a string. Any match is
5637 <sect1>talk <call> > <node> [<text>] (0)
5641 <bf>talk <call> > <node> [<text>]</bf> Send a text message to another station via a node
5645 Send a short message to any other station that is visible on the cluster
5646 system. You can send it to anyone you can see with a SHOW/CONFIGURATION
5647 command, they don't have to be connected locally.
5649 The second form of TALK is used when other cluster nodes are connected
5650 with restricted information. This usually means that they don't send
5651 the user information usually associated with logging on and off the cluster.
5653 If you know that G3JNB is likely to be present on GB7TLH, but you can only
5654 see GB7TLH in the SH/C list but with no users, then you would use the
5655 second form of the talk message.
5657 If you want to have a ragchew with someone you can leave the text message
5658 out and the system will go into 'Talk' mode. What this means is that a
5659 short message is sent to the recipient telling them that you are in a
5660 'Talking' frame of mind and then you just type - everything you send will
5661 go to the station that you asked for.
5663 All the usual announcements, spots and so on will still come out on your
5666 If you want to do something (such as send a spot) you preceed the normal
5667 command with a '/' character, eg:-
5670 /DX 14001 G1TLH What's a B class licensee doing on 20m CW?
5674 To leave talk mode type:
5680 If you are in 'Talk' mode, there is an extention to the '/' command which
5681 allows you to send the output to all the people you are talking to. You do
5682 with the '//' command. For example:-
5688 will send the hftable as you have it to all the people you are currently
5690 <sect1>talk <call> [<text>] (0)
5694 <bf>talk <call> [<text>]</bf> Send a text message to another station
5698 <sect1>type <filearea>/<name> (0)
5702 <bf>type <filearea>/<name></bf> Look at the contents of a file in one of the fileareas
5706 Type out the contents of a file in a filearea. So, for example, in
5707 filearea 'bulletins' you want to look at file 'arld051' you would
5710 TYPE bulletins/arld051
5713 See also SHOW/FILES to see what fileareas are available and a
5715 <sect1>uncatchup <node call> all|[msgno> ...] (5)
5719 <bf>uncatchup <node call> all|[msgno> ...]</bf> Unmark a message as sent
5723 When you send messages the fact that you have forwarded it to another node
5724 is remembered so that it isn't sent again. When you have a new partner
5725 node and you add their callsign to your /spider/msg/forward.pl file, all
5726 outstanding non-private messages will be forwarded to them. This may well
5727 be ALL the non-private messages. You can prevent this by using these
5732 catchup GB7DJK 300 301 302 303 500-510
5735 and to undo what you have just done:-
5738 uncatchup GB7DJK all
5739 uncatchup GB7DJK 300 301 302 303 500-510
5742 which will arrange for them to be forward candidates again.
5744 Order is not important.
5745 <sect1>unset/announce (0)
5749 <bf>unset/announce</bf> Stop announce messages coming out on your terminal
5753 <sect1>unset/anntalk (0)
5757 <bf>unset/anntalk</bf> Stop talk like announce messages on your terminal
5761 The announce system on legacy cluster nodes is used as a talk
5762 substitute because the network is so poorly connected. If you:
5768 you will suppress several of these announces, you may miss the odd
5769 useful one as well, but you would probably miss them anyway in the
5770 welter of useless ones.
5776 allows you to see them again. This is the default.
5777 <sect1>unset/baddx <call>.. (8)
5781 <bf>unset/baddx <call>..</bf> Propagate a dx spot with this callsign again
5785 Setting a word as 'baddx' will prevent spots with that word in the
5786 'spotted' field (as in: DX 14001.1 FR0G)of a DX spot from going any
5787 further. They will not be displayed and they will not be sent onto
5790 The word must be written in full, no wild cards are allowed eg:-
5793 set/baddx FORSALE VIDEO FR0G
5796 To allow a word again, use the following command ...
5802 <sect1>unset/badnode <call>.. (8)
5806 <bf>unset/badnode <call>..</bf> Allow spots from this node again
5810 Setting a callsign as a 'badnode' will prevent spots from that node
5811 going any further. They will not be displayed and they will not be
5812 sent onto other nodes.
5814 The call must be a full eg:-
5820 will stop anything from K1TTT. If you want SSIDs as well then you must
5821 enter them specifically.
5827 will allow spots from him again.
5829 Use with extreme care. This command may well be superceeded by FILTERing.
5830 <sect1>unset/badspotter <call>.. (8)
5834 <bf>unset/badspotter <call>..</bf> Allow spots from this callsign again
5838 Setting a callsign as a 'badspotter' will prevent spots from this callsign
5839 going any further. They will not be displayed and they will not be
5840 sent onto other nodes.
5842 The call must be written in full, no wild cards are allowed eg:-
5845 set/badspotter VE2STN
5848 will stop anything from VE2STN. This command will automatically
5849 stop spots from this user, regardless of whether or which SSID
5850 he uses. DO NOT USE SSIDs in the callsign, just use the callsign
5854 unset/badspotter VE2STN
5857 will allow spots from him again.
5859 Use with extreme care. This command may well be superceded by FILTERing.
5860 <sect1>unset/badword <word>.. (8)
5864 <bf>unset/badword <word>..</bf> Propagate things with this word again
5868 Setting a word as a 'badword' will prevent things like spots,
5869 announces or talks with this word in the the text part from going any
5870 further. They will not be displayed and they will not be sent onto
5873 The word must be written in full, no wild cards are allowed eg:-
5876 set/badword annihilate annihilated annihilation
5879 will stop anything with these words in the text.
5882 unset/badword annihilated
5885 will allow text with this word again.
5886 <sect1>unset/beep (0)
5890 <bf>unset/beep</bf> Stop beeps for DX and other messages on your terminal
5894 <sect1>unset/debug <name> (9)
5898 <bf>unset/debug <name></bf> Remove a debug level from the debug set
5902 You can choose to log several different levels. The levels are
5912 You can show what levels you are logging with SHOW/DEBUG
5917 <bf>unset/dx</bf> Stop DX messages coming out on your terminal
5921 <sect1>unset/dxcq (0)
5925 <bf>unset/dxcq</bf> Stop CQ Zones on the end of DX announcements
5929 Display both the Spotter's and the Spotted's CQ Zone on the end
5930 of a DX announcement (there is just enough room). Some user programs
5931 cannot cope with this. The Spotter's CQ is on the RHS of the
5932 time, the Spotted's CQ is on the LHS.
5934 Conflicts with: SET/DXGRID, SET/DXITU, SHOW/USSTATE
5936 Do a STAT/USER to see which flags you have set if you are confused.
5937 <sect1>unset/dxgrid (0)
5941 <bf>unset/dxgrid</bf> Stop QRA Grid Squares on the end of DX announcements
5945 A standard feature which is enabled in version 1.43 and above is
5946 that if the spotter's grid square is known it is output on the end
5947 of a DX announcement (there is just enough room). Some user programs
5948 cannot cope with this. You can use this command to reset (or set)
5951 Conflicts with: SET/DXCQ, SET/DXITU
5953 Do a STAT/USER to see which flags you have set if you are confused.
5954 <sect1>unset/dxitu (0)
5958 <bf>unset/dxitu</bf> Stop ITU Zones on the end of DX announcements
5962 Display both the Spotter's and the Spotted's ITU Zone on the end
5963 of a DX announcement (there is just enough room). Some user programs
5964 cannot cope with this. The Spotter's ITU is on the RHS of the
5965 time, the Spotted's ITU is on the LHS.
5967 Conflicts with: SET/DXGRID, SET/DXCQ, SHOW/USSTATE
5969 Do a STAT/USER to see which flags you have set if you are confused.
5970 <sect1>unset/echo (0)
5974 <bf>unset/echo</bf> Stop the cluster echoing your input
5978 If you are connected via a telnet session, different implimentations
5979 of telnet handle echo differently depending on whether you are
5980 connected via port 23 or some other port. You can use this command
5981 to change the setting appropriately.
5983 The setting is stored in your user profile.
5985 YOU DO NOT NEED TO USE THIS COMMAND IF YOU ARE CONNECTED VIA AX25.
5986 <sect1>unset/email (0)
5990 <bf>unset/email</bf> Stop personal msgs being forwarded by email
5994 If any personal messages come in for your callsign then you can use
5995 these commands to control whether they are forwarded onto your email
5996 address. To enable the forwarding do something like:-
5999 SET/EMAIL mike.tubby@somewhere.com
6002 You can have more than one email address (each one separated by a space).
6003 Emails are forwarded to all the email addresses you specify.
6005 You can disable forwarding by:-
6011 <sect1>unset/here (0)
6015 <bf>unset/here</bf> Tell the system you are absent from your terminal
6019 <sect1>unset/hops <call> ann|spots|route|wwv|wcy (8)
6023 <bf>unset/hops <call> ann|spots|route|wwv|wcy</bf> Unset hop count
6027 Set the hop count for a particular type of broadcast for a node.
6029 This command allows you to set up special hop counts for a node
6030 for currently: announce, spots, wwv and wcy broadcasts.
6034 set/hops gb7djk ann 10
6035 set/hops gb7mbc spots 20
6038 Set SHOW/HOPS for information on what is already set. This command
6039 creates a filter and works in conjunction with the filter system.
6041 You can unset the hops with command UNSET/HOPS. For example:-
6044 unset/hops gb7djk ann
6045 unset/hops gb7mbc spots
6048 <sect1>unset/isolate (9)
6052 <bf>unset/isolate</bf> Stop Isolation of a node from the rest of the network
6056 Remove isolation from a node - SET/ISOLATE
6057 <sect1>unset/lockout <call> (9)
6061 <bf>unset/lockout <call></bf> Allow a callsign to connect to the cluster
6065 <sect1>unset/logininfo (0)
6069 <bf>unset/logininfo</bf> Inform when a station logs out locally
6073 <sect1>unset/password <call> ... (9)
6077 <bf>unset/password <call> ...</bf> Delete (remove) a user's password
6081 This command allows the sysop to completely delete and remove a
6082 password for a user.
6083 <sect1>unset/privilege (0)
6087 <bf>unset/privilege</bf> Remove any privilege for this session
6091 You can use this command to 'protect' this session from unauthorised
6092 use. If you want to get your normal privilege back you will need to
6093 either logout and login again (if you are on a console) or use the
6095 <sect1>unset/prompt (0)
6099 <bf>unset/prompt</bf> Set your prompt back to default
6103 This command will set your user prompt to exactly the string that you
6104 say. The point of this command to enable a user to interface to programs
6105 that are looking for a specific prompt (or else you just want a different
6112 UNSET/PROMPT will undo the SET/PROMPT command and set you prompt back to
6114 <sect1>unset/register <call> ... (9)
6118 <bf>unset/register <call> ...</bf> Mark a user as not registered
6122 Registration is a concept that you can switch on by executing the
6125 set/var $main::regreq = 1
6128 command (usually in your startup file)
6130 If a user is NOT registered then, firstly, instead of the normal
6131 motd file (/spider/data/motd) being sent to the user at startup, the
6132 user is sent the motd_nor file instead. Secondly, the non registered
6133 user only has READ-ONLY access to the node. The non-registered user
6134 cannot use DX, ANN etc.
6136 The only exception to this is that a non-registered user can TALK or
6137 SEND messages to the sysop.
6139 <sect1>unset/talk (0)
6143 <bf>unset/talk</bf> Stop TALK messages coming out on your terminal
6147 <sect1>unset/usstate (0)
6151 <bf>unset/usstate</bf> Stop US State info on the end of DX announcements
6155 If the spotter's or spotted's US State is known it is output on the
6156 end of a DX announcement (there is just enough room).
6158 A spotter's state will appear on the RHS of the time (like
6159 SET/DXGRID) and the spotted's State will appear on the LHS of the
6160 time field. Any information found will override any locator
6161 information from SET/DXGRID.
6163 Some user programs cannot cope with this. You can use this command
6164 to reset (or set) this feature.
6166 Conflicts with: SET/DXCQ, SET/DXITU
6168 Do a STAT/USER to see which flags you have set if you are confused.
6169 <sect1>unset/wcy (0)
6173 <bf>unset/wcy</bf> Stop WCY messages coming out on your terminal
6177 <sect1>unset/wwv (0)
6181 <bf>unset/wwv</bf> Stop WWV messages coming out on your terminal
6189 <bf>unset/wx</bf> Stop WX messages coming out on your terminal
6197 <bf>who</bf> Show who is physically connected
6201 This is a quick listing that shows which callsigns are connected and
6202 what sort of connection they have
6203 <sect1>wx <text> (0)
6207 <bf>wx <text></bf> Send a weather message to local users
6211 <sect1>wx full <text> (0)
6215 <bf>wx full <text></bf> Send a weather message to all cluster users
6219 <sect1>wx sysop <text> (5)
6223 <bf>wx sysop <text></bf> Send a weather message to other clusters only
6227 Weather messages can sometimes be useful if you are experiencing an extreme
6228 that may indicate enhanced conditions